0
What VLANs are allowed across a trunk when the range of allowed VLANs is set to the default value?
Wiki User
∙ 11y ago
all VLANs
The default is to allow all VLANs through the trunking ports.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the network ID and what is the host id of ip address 110.10.10.1?
Assuming that this is a Class A network (Class A Networks range from 1-127) the default subnet masked is 255.0.0.0. Therefore the network ID would be 110.0.0.0 and the host ID would be x.10.10.1
Define domain with respect to dbms?
In database technology, domain refers to the description of an attribute's allowed values. The physical description is a set of values the attribute can have, and the semantic, or logical, description is the meaning of the attribute.
Technology has ethical issues. a.expanded the range of b.reduced the range of c.made little difference on the range of d.eliminated most?
Technology has .............. ethical issues a.expanded the range of b.reduced the range of c.made little difference on the range of d.eliminated lost
In what situations would you want to have narrow tonal range versus wide tonal range?
In what situations would you want to have narrow tonal range versus wide tonal range?
What should you do to ensure that DHCP does not assign the addresses you have statically assigned to the network servers?
Simple assign the range in the DHCP Server after excluding some IPs For the Network Server(s). But if suppose you have already assigned the range and want to configure a static IP for the server in that range only, then just add the exclusion range in DHCP that you don't want DHCP to use for distribution. Exclusion range can be of one IP also. Hope this helped -- By MyNarutoAnime
Extended range vlans are identified by a vlan id between what ranges?
1006 and 4094
How do you create VLAN step-by-step?
AnswerVLANs are created on Layer 2 switches to control broadcasts and enforce the use of a Layer 3 device for communications. Each VLAN is created in the local switch's database for use. If a VLAN is not known to a switch, that switch cannot transfer traffic across any of its ports for that VLAN. VLANs are created by number, and there are two ranges of usable VLAN numbers (normal range 1-1000 and extended range 1025-4096). When a VLAN is created, you can also give it certain attributes such as a VLAN name, VLAN type, and its operational state. To create a VLAN, use the following steps.1) Configure VTP. VTP is a protocol used by Cisco switches to maintain a consistent database between switches for trunking purposes. VTP is not required to create VLANs; however, Cisco has set it up to act as a conduit for VLAN configuration between switches as a default to make administration of VLANs easier. Because of this, you must first either configure VTP with a domain name or disable VTP on the switch.2) Create the VLAN. VLANs are created by number. The two ranges of VLANs are as follows: The standard range consists of VLANs 1 to 1000. The extended range consists of VLANs 1025 to 4096. Extended VLANs are currently supported only on switches running COS software version 6.1 or greater. When you create a VLAN, you have many options to consider. Many options are valid only for FDDI and Token Ring VLANs. Some of the items configured deal with options, such as private VLANs, which are discussed in other sections in this book. VLANs are created using the set vlan command for COS devices or with the vlan command in vlan database mode for IOS switches.
What are two characteristics of normal range vlans?
-can contain ports used as trunks -identified by a VLAN ID between 1 and 1005
What are similarities across a range of group?
similarities across a range of groups
How does a diode shorted?
due to high voltage across the diode ie more than piv of the diode or current flows more than maximum allowed range of diode.
What is the mountain range that spreads across oregon and washington?
Cascade range
What mountain range runs north to south across Australia?
The Great Dividing Range runs north to south across Australia, stretching over 2,175 miles from the northeastern tip of Queensland to the state of Victoria. It is the third-longest land-based mountain range in the world.
Does Arizona or Louisiana have a higher mountain range?
Arizona wins by default, because there are no mountains in Louisiana.
What mountain range across Europe and Asia?
the himalayas
What are the Advantages of having a gear in a car?
The gearbox found in a car allows the engine to perform across its most efficient rev range - or across the range it produces the most torque.
What mountain range runs from north to south across Australia?
The Great Dividing Range is a mountain range that runs from north to south along the eastern coast of Australia. It is one of Australia's most significant geographical features, stretching over 3,500 kilometers.
What is the name of the mountain range that runs across Antarctica?
You may be thinking of the Trans-Antarctic mountain range.
