0
a nonsense question
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What does cathode ray tube mean?
A cathode ray tube is what was used in televisions and computer monitors before the advent of the LCD, LED, and Plasma tv screens. They are big, bulky, and very heavy. They are a vacuum tube, with an approximately flat face, on the inner surface of which is deposited a phosphor. When electrons from the cathode asembly reach the phosphor, they cause it to glow at that spot.
How bright is a 3000k led?
It depends on the wattage and how much light the LED emits. 3000K refers to the color temperature of the light and has no relationship to brightness.
How do you Connect LED lights together?
LEDs are semiconductor devices that behave like diodes. In general they have a 1.7 volt forward voltage drop (anode+ to cathode-)when conducting and emitting light. When they are connected together in a series type electrical connection you must obey the polarity (connect cathode of each to anode of next diode)and be certain you don't exceed the allowable reverse voltage rating of the device as well as the forward allowable current. Therefore to use LEDs in a 120 Volt AC household circuit The peak voltage will be 170 volts and you will need 170/1.7 = 100 LEDs connected in series. You will also need 100 LEDs wired in the opposite polarity to avoid exceeding the reverse voltage. Half the LEDs will light on each of the AC cycles.
What is horizontal and vertical amplifier in cathode ray oscilloscope?
The horizontal and vertical amplifier in the cathode-ray oscilloscope are deflection plates. The horizontal amplifier causes the beam to be deflected horizontally at a rate that is uniform. The vertical amplifier causes the beam to deflect vertically.
What is the screen on your computer called where all the icons are?
The screen on a computer is part of a monitor. It is referred as the monitor "panel" or as the "display surface" The latter is the surface of the large end of a cathode ray tube, where images are created.
How do you wire Bi-color LEDs?
Treat each color as a separate LED and wire accordingly. Be sure to observe the polarity of the component (anode and cathode +/-)
How do you wire Bi color LEDs?
Treat each color as a separate LED and wire accordingly. Be sure to observe the polarity of the component (anode and cathode +/-)
How is led cathode identified on PC board?
A: LED will have a visual greater real estate on the cathode side it can be seen if the LED is transparent other way is using a VOM and measure the potential . the less potential will be at the cathode.
How can you identify a cathode nigative to an LED?
LED has two pins,one is anode(positive) and the other is cathode(negative).The smaller pin is cathode(negative) and the longer pin is anode(positive).
Is the short lead the cathode on an led?
Yes
What is the difference between anode led and cathode led?
A: A LED is a diode and like all diode they have an [anode] meaning positive terminal and a [cathode] negative terminal. Therefore the proper potential must be applied for it to behave like an LED.
Forward current of led?
The forward current of an LED is current that goes from the anode of the LED to the cathode (the forward direction).
0n an LED what are the names of the positive and the negative leg?
Anode and cathode. Anode = negative lead, cathode = positive lead.
What is the left leg of the led called?
Cathode and an anodeThey are called the "anode" and the "cathode", just like every other diode ever built.
What is LED Forward Voltage?
The forward voltage of an LED is the voltage that must be applied across the leads of an LED, anode to cathode, in order for the LED to function and turn on.
Does a cathode ray produce red fluorescence?
The cathode ray is just a beam of electrons. The color of the fluorescence depends on the substance in the target.
What is the short and long legs of LED called?
Cathode (negative) is the shortest leg and there is a flat edge on the base of the LED, and it must be connected to the negative wire or "-" connection. Anode (positive) is the longest leg, and must be connected to the positive wire or "+" connection, as electricity will only pass through a LED from positive to negative.
