Token ring hub
In networking, a token passing topology is a method where a special data packet, called a token, circulates around the network. Only the device that holds the token can send data, ensuring organized access and reducing collisions. This approach enhances network efficiency and reliability by controlling the flow of data between devices. Examples of token-based protocols include Token Ring and Token Bus.
For two or more connected networks you can use a bridgeto connect them all together.It depends on the two networks. A bridge can only connect two networks of the same type (eg Ethernet or Token-Ring), that also use the same layer 3 network address (eg IP subnet or IPX network #, or AppleTalk network #).A "gateway" device can connect two dissimilar types that share a network address, and a router can connect two networks of different network addresses whether or not they have the same network type.
That's called a "token".That's called a "token".That's called a "token".That's called a "token".
3. Unlike Ethernet, Token Ring uses a ring topology whereby the data is sent from one machine to the next and so on around the ring until it ends up back where it started. It also uses a token passing protocol which means that a machine can only use the network when it has control of the Token, this ensures that there are no collisions because only one machine can use the network at any given time.
Uranus
it is a network data communication system where each of the device connected with it wait for their time to communicate. when they have the token, they got to communicate or sent transmission.
In networking, a token passing topology is a method where a special data packet, called a token, circulates around the network. Only the device that holds the token can send data, ensuring organized access and reducing collisions. This approach enhances network efficiency and reliability by controlling the flow of data between devices. Examples of token-based protocols include Token Ring and Token Bus.
You will need a router. Token Ring and Ethernet refer to two different layer two protocols. You will need a layer three device to encapsulate the data for communication between the two networks. A bridge refers to a layer two device.
A center connectivity device means a star topology is being used. If it is a managed hub such as a MAU or MSAU unit, then it is a token ring network.
I assume you're talking about a network. On a token network, all of the computers wait to send data until they have the token. The token is a piece of data that travels around the network (picture all of the computers set up in a circle) giving each one a chance to send their data. After that computer has sent the data, the token moves on to the next. It prevents data collision on the network.
Although Token Ring uses a logical ring to transmit data, it is wired as a star through a device called a multi-station access unit, or MSAU. The MSAU actually contains the ring within it, and when a node connects to the MSAU it opens a relay circuit allowing data to flow down to the newly-connected node. Internetworking with Cisco and Microsoft Technologies pg. 233
Fddi can be further connected to other networks whereas token ring is individual network of computers.
A ring topology requires several key components: network devices (such as computers and printers) that are connected in a circular fashion, a network interface card (NIC) in each device to enable communication, and cabling to connect each device to its two adjacent devices in the ring. Additionally, a token-passing mechanism may be used to control data transmission, ensuring that only one device sends data at a time to prevent collisions. This setup allows for efficient data transfer but can be disrupted if any single device or connection fails.
What is this 'device' you are referring to? Are you using your phone lines in your house to run a network? If so, then no, it will be almost impossible to run a DSL modem to that network. The reason is, a phone line network, which typically runs at 1mb per second, uses 'token ring' methology... basically one computer holds the 'token' and the other computers are constantly asking for it, and it travels ONE direction, not 2 way communication. For the price, I would install network cards in all your computers, and run CAT5 cable, with a router near your DSL Modem. that way, the DSL modem will see one computer, but all the computers, attached to the router via CAT5 cable, will be able to access the internet.
Because it makes all computers who have something to say wait until they get the token. Some info that needs to be sent may be very important but if it doesn't have the token then too bad. It'll have to wait.
it is a network data communication system where each of the device connected with it wait for their time to communicate. when they have the token, they got to communicate or sent transmission.
i think it means you can't connect xD I get it all the time