0
T-568A and T-568B are two types of wiring for the connectors on ethernet cables. Both standards work fine, but you can not intermix the two types of connectors on a single cable. You can have mixed cables on a network as long as each individual cable is wired the same on both ends. (Example, one patch cable uses t568a on both ends, a different cable uses t568b on both ends, and a third uses a matching, but different color pinout)
Some cable is labeled 568a or 568b. This means that the 4 twisted pairs (for a total of 8 little cables) inside the jacketed ethernet cable is made for a certain type of connection. For example, cat 6 cable is higher quality, rated for up to 10GB network use. There are more twists per inch of those little wire pairs inside the jacket of the cable to help reduce crosstalk and interference. I have some cat 6 cable labeled 568b, and of the 4 twisted pairs, some have more twists then others. corresponding to what the data pairs are in the cable. I assume this is a cost cutting measure as more twists means more wire inside of those ethernet cables. Better quality cable should have equal amounts of twists per inch so that either 568a or 568b connections can be used without having to worry about what the cable specifies.
What else can I help you with?
Can CAT5 wire be used to supply power?
Yes. A Cat-5 line can be used to supply power to certain Ethernet Switches that support POE, or Power Over Ethernet.
What causes lost frames on Ethernet?
You might have poor connectivity. The wire could be marred in some way.
Can a Ethernet tranceiver be used to adapt a phone the the internet?
No. An ethernet transceiver is for connecting only to ethernet cable - 8 wires. Phone wire has 4 or 6 - not enough (plus plug is too small.) You need a modem to connect to a service provider over phone lines.
Which port is used to connect your computer to a network?
The "Ethernet Port" Obviously is used for the Ethernet cable which often connects computers to a router. A router is a device that gets the Internet or from the phone/Internet port and routes it to your computer routers are required for ADSL and ADSL2+ to work. Oftener more than one computer is connected to the router. But this setup may be different for "Cable Internet because i have never had cable.
What Devices is used to connect a computer to a network?
Modem.
How i should make crossover cable?
I am assuming you have bulk cable available, RJ-45 connectors and a crimping tool. Wire one end of the cable using the T568-A wiring standard, and the other using T568-B. That's your crossover cable.
How do you play playstation3 with out ethernet wire?
Take the Ethernet cable out from it.
What kind of wire is used with cable modem?
Coaxial and ethernet. The round one is coaxial, the rectangular ones are ethernet.
How much does an Ethernet wire cost?
Harrison is awsome and is the best
How do you connect your WiFi laptop to your desktop internet?
Step 1. Unplug ethernet wire from desktop computer. Step 2. Plug the ethernet wire you just removed into your laptop's ethernet port. Step 3. When finished browsing the internet or when portability is desired, disconnect the ethernet cable from laptop and return to the port on the desktop.
Which wire have been used to connect PC and router?
ethernet cable
How to wire a house for ethernet effectively and efficiently?
To wire a house for ethernet effectively and efficiently, plan the layout carefully, use high-quality ethernet cables, install wall jacks in each room, and connect everything to a central network switch. Consider hiring a professional for complex installations.
How to wire a house for ethernet?
To wire a house for ethernet, you will need to plan the layout, run ethernet cables through walls and ceilings, terminate the cables with connectors, and connect them to a central network switch or router. It is important to follow safety guidelines and consider factors like cable length and placement for optimal performance.
Do you need a wire for ps2 network adapter?
Yes you do, you need a internet(ethernet cable).
How to wire a PoE Ethernet cable for power and data transmission?
To wire a PoE Ethernet cable for power and data transmission, you need to use a cable that supports Power over Ethernet (PoE) and has the necessary connectors. Connect the Ethernet cable to a PoE injector or switch, ensuring that the correct wires are matched for power and data transmission. Follow the manufacturer's instructions for proper wiring and configuration to ensure successful power and data transmission over the Ethernet cable.
What is the name of the wire you need to playmultiplayer on ps3?
The wire is an ethernet cable and you must have internet service and not just the wire. The Ethernet Cable plugs into the back of the PS3 and into the router or modem for a wired connection that will not be established until after you have gone to the settings menu for network connections and set up the automatic connection
Is Brother 420 nc a wireless printer?
No, this is not a wireless printer. If you want, you can wire it into your Ethernet network and then it might work as a wireless printer if the Ethernet connects to a WiFi router.
