0
What else can I help you with?
What does the passive command provide to dynamic routing protocols?
Perhaps you mean the "passive-interface" command in Cisco routers; what this does is that no information related to the routing protocol will be sent through the specified interface. For example, the interface that connects your network to the ISP should not carry any routing protocol information, since the routing protocol is only useful within your company's network.
What is a network interface print device?
The routers are configured with different versions of RIP. R2 is not forwarding the routing updates. The R1 configuration should include the no auto-summary command. The maximum path number has been exceeded.
Which table does a router use to make decisions about the interface through which a data packet is to be sent?
Routing table
Which router component holds the routing table ARP cache and running configuration file?
SDRAM
How many physical interfaces are required to perform inter-VLAN routing with traditional inter-VLAN routing?
In traditional inter-VLAN routing (also known as "router-on-a-stick"), only one physical interface is required on the router. However, this single physical interface needs to be configured with multiple sub interfaces, each corresponding to a different VLAN. The router uses these sub interfaces to route traffic between VLANs. The configuration involves: One physical interface on the router (e.g., GigabitEthernet0/1). Multiple sub interfaces (e.g., GigabitEthernet0/1.10, GigabitEthernet0/1.20) corresponding to different VLANs. Each sub interface is assigned an IP address in the respective VLAN's subnet. This setup enables inter-VLAN routing by allowing the router to route traffic between the VLANs using a single physical interface.
IDentify the data categories that are used to create a network configuration table for a router?
Interface name IP routing protocols
What are the minimum elements that you should find in a routing table?
A list of destination networks known by the router & the reachable interface for the route that goes to each network.
How do you stop rip routing updates?
To stop RIP (Routing Information Protocol) routing updates, you can use the "passive-interface" command on routers to prevent the interface from sending RIP updates. This command can be applied to specific interfaces using the router configuration mode. Additionally, you can disable RIP entirely by removing the RIP configuration from the router or using the "no router rip" command. Finally, implementing route filtering with access control lists (ACLs) can also help control the propagation of RIP updates.
What command is used to stop rip routing updates from exiting out an interface but still allow the interface to receive rip route updates?
Router(config-if)#no routing
Which two components are used to determine the router ID in the configuration of the OSPF routing process?
the highest IP address of any logical interfacethe highest IP address of any physical interface
Which command or set of commands will stop an RIP routing process?
To stop an RIP routing process on a Cisco router, you can use the command no router rip in global configuration mode. This command removes the RIP configuration and stops the RIP routing process from running. Alternatively, you can use shutdown within the RIP routing configuration mode to disable RIP without removing its configuration.
What does the passive-interface command do?
Passive-interface command is used in all routing protocols to disable sending updates out from a specific interface.
When a Cisco router is being moved from an IPv4 network to a complete IPv6 environment which series of commands would correctly enable IPv6 forwarding and interface addressing?
To enable IPv6 forwarding and configure interface addressing on a Cisco router moving to an IPv6 environment, you would first enter global configuration mode and enable IPv6 routing with the command ipv6 unicast-routing. Next, you would access the specific interface using interface <interface-name> and assign an IPv6 address with the command ipv6 address <ipv6-address>/<prefix-length>. Finally, use the command no shutdown to activate the interface.
What does the passive command provide to dynamic routing protocols?
Perhaps you mean the "passive-interface" command in Cisco routers; what this does is that no information related to the routing protocol will be sent through the specified interface. For example, the interface that connects your network to the ISP should not carry any routing protocol information, since the routing protocol is only useful within your company's network.
When do directly connected networks appear in the routing table?
Directly connected networks appear in the routing table when a network interface on a router is configured with an IP address and subnet mask, and the interface is in an "up" state. The router automatically adds these networks to its routing table as local routes, allowing it to route traffic directly to those networks without needing additional configuration or protocols. This ensures that the router can efficiently communicate with devices on those directly connected networks.
What is passive interface?
A passive interface is a feature in networking where an interface still participates in routing updates, but it does not actively send or receive information. This can be useful to prevent unnecessary routing updates from being sent out on specific interfaces, reducing network traffic and overhead.
When a router does not have an interface for the destination network it sends the traffic to where?
If a router has a route in its routing table, it will have a next hop IP address and / or outbound interface. If a router does not have a route in its routing table the packet will be dropped.
