The subnet mask must match for all NICs in a LAN, otherwise the packets must be forwarded to another network via a router.
The correct answer is "frame type".
The frame type must match in the communications between all NICs on a network.
Communications
NICs stands for network interface controller. In computer networking, a NIC provides the hardware interface between a computer and a network. A NIC technically is network adapter hardware in the form factor of an add-in card such as a PCI or PCMCIA card.
A Network Interface Card helps provide an Interface (or access) to network resources, the internet, and networks outside your LAN (local area network.)In computer networking, a NIC provides the hardware interface between a computer and a network. A NIC technically is network adapter hardware in the form factor of an add-in card such as a PCI or PCMCIA card.Some NIC cards work with wired connections while others are wireless. Most NICs support either wired Ethernet or WiFi wireless standards. Ethernet NICs plug into the system bus of the PC and include jacks for network cables, while WiFi NICs contain built-in transmitters / receivers (transceivers).Also Known As: NIC also stands for Network Information Center. For example, the organization named "InterNIC" is a NIC that provides information to the general public on Internet domain names.
Limited Broadcast - Sent to all NICs on the some network segment as the source NIC. It is represented with the 255.255.255.255 TCP/IP address. This broadcast is not forwarded by routers so will only appear on one network segment.Direct broadcast - Sent to all hosts on a network. Routers may be configured to forward directed broadcasts on large networks. For network 192.168.0.0, the broadcast is 192.168.255.255.
A peer-to-peer (P2P) network is a type of computer network in which each computer, or node, in the network acts as both a client and a server, allowing for decentralized sharing of resources and information. P2P networks can use a variety of peripheral devices to connect and share data between nodes. One common peripheral device used in P2P networks is the network interface card (NIC), which allows computers to connect to a network and communicate with other devices. The NIC is responsible for transmitting and receiving data over the network, and can be either wired or wireless. Wired NICs use an Ethernet cable to connect to a router or switch, while wireless NICs use Wi-Fi technology to connect to a wireless network. Another peripheral device commonly used in P2P networks is the external hard drive. External hard drives allow users to store and share large amounts of data, such as documents, photos, and videos, between nodes in the network. External hard drives can be connected to a computer through a USB or FireWire port, and can be accessed by other computers in the network through file sharing software or a network-attached storage (NAS) device. The use of external hard drives in P2P networks allows for easy sharing and backup of important data, without the need for expensive and complex server systems.
Communications
"2-nic" is a term commonly used in virtualization to refer to a server or computer with two network interface cards (NICs). Having 2 NICs allows for managing network traffic more efficiently by segregating different types of communications or providing redundancy for improved network reliability.
c. in the NICs
The network interface cards (NICs) connectors cables
NICs stands for network interface controller. In computer networking, a NIC provides the hardware interface between a computer and a network. A NIC technically is network adapter hardware in the form factor of an add-in card such as a PCI or PCMCIA card.
A zero-slot LAN is a local-area network (LAN) that uses existing serial and/or parallel communication ports on the computers in the network instead of requiring network interface cards (NICs) that would occupy an expansion slot. Advantages It leads to transmitting between computers over a serial or parallel port, thus freeing up an expansion slot normally used by LAN cards (NICs). Disadvantages Zero-slot LANs are typically slower than LANS that use NICs and are limited to two or three network nodes.
The NIC is the interface device between the computer's data bus and the network. It contains the transmitter and receiver necessary to send and receive signals. It also has memory to help with network performance and some types of NICs also contain microprocessors to help off-load the work from the main computer CPU. A NIC also contains the physical connections required to send and receive electrical or wireless signals on a LAN.
Yes, NICs can be a form of expansion card (as long as the NIC is not built into the motherboard).
wireless access points, wireless network interface cards (NICs) and routers.
A Network Interface Card helps provide an Interface (or access) to network resources, the internet, and networks outside your LAN (local area network.)In computer networking, a NIC provides the hardware interface between a computer and a network. A NIC technically is network adapter hardware in the form factor of an add-in card such as a PCI or PCMCIA card.Some NIC cards work with wired connections while others are wireless. Most NICs support either wired Ethernet or WiFi wireless standards. Ethernet NICs plug into the system bus of the PC and include jacks for network cables, while WiFi NICs contain built-in transmitters / receivers (transceivers).Also Known As: NIC also stands for Network Information Center. For example, the organization named "InterNIC" is a NIC that provides information to the general public on Internet domain names.
Media Access Control address (MAC address) is a unique identifier assigned to most network adapters or network interface cards (NICs) by the manufacturer for identification.
NICs do not connect to applications, rather they connect to other wireless devices. IEEE 802.1 is the standard used to connect wireless NICs to other network devices.