0
What else can I help you with?
What address does the router use to compare to the routing table?
in general the router uses the network address to compare to the routing table. Specifically, on the internet, the Router looks up the destination IP address in the router table to determine where to route the packet.
Which command or set of commands will stop the RIP routing process?
no router rip
What is the effect of configuring the IPv6 unicast-routing command on a router?
By configuring an IPv6 Unicast routing command on a router you are allowing the router to communicate with the IPv6 interface. This is needed if you intend to send or receive data over an IPv6 network.
What is a router on stick inter vlan routing?
A physical router device with an interface that routes between two or more VLANs that are attached to a VLAN network segment by a trunk link. In other words a " router on a [ TRUNK ] " which is originating from switches with independent non routing VLANs.
What is RIP routing protocol?
RIP is a routing protocol - a protocol (set of rules) that allows a router to exchange information, with other routers, about existing routes.
What is different between router and routing?
*router is a device use to route communication or connection *routing is the process *router is a device use to route communication or connection *routing is the process
Describe the role of the routing table on a host and on a router?
Describe the role of the routing table on a host and on a router.
What is the similarities and differences between the windows routing table and the router routing table?
That depends entirely on what Operating System the router is running
What are three features of router-on-a-stick inter-VLAN routing?
What are three features of router-on-a-stick, inter-VLAN routing? (Choose three.)
When a router does not have an interface for the destination network it sends the traffic to where?
If a router has a route in its routing table, it will have a next hop IP address and / or outbound interface. If a router does not have a route in its routing table the packet will be dropped.
How do you enable ip routing to yes?
On a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routingOn a Cisco router, the command to enable IP routing (for IPv4) is:ip routingTo disable it:no ip routing
What comment are use to delete a routing protocols in cisco router?
No router eigrp <AS #> No router ospf <process ID> No router bgp <AS #> No router rip
What address does the router use to compare to the routing table?
in general the router uses the network address to compare to the routing table. Specifically, on the internet, the Router looks up the destination IP address in the router table to determine where to route the packet.
How do you set default root in a router by using dynamic routing?
If the network uses the RIP protocol, router A will determine that all paths have equal cost. If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table. If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest cost. If both RIP and EIGRP protocols are configured on router A, the router will use the route information that is learned by the RIP routing protocol.
What is the advantage of dynamic routing?
The router needs a routing table, to know where to send IP packets. The purpose of dynamic routing is to update the routing tables automatically. This means you need much less configuration, and the network dynamically adjusts to topology changes (for example, a router is added, or a cable has a bad connection).
Which command or set of commands will stop the RIP routing process?
no router rip
What are the best practices for routing plywood to achieve precise and clean cuts?
To achieve precise and clean cuts when routing plywood, it is important to use a sharp router bit, secure the plywood firmly in place, move the router slowly and steadily, and make multiple shallow passes rather than one deep cut. Additionally, using a straight edge or template can help guide the router for more accurate cuts.
