Unless your hub has a switchable port, you use a crossover cable.
tpatch cable is also known as straight cable and mostly connected same devices or nodes. but on the other side cross cable is just different then patch and used to connect different devices. Hem Gurjar
To link 2 computers you should have cross cable. Because Serial cable is user to connect 2 or more dissimilar devices. To connect 2 similar devices like computers, Hubs, Switches you should use Cross cable only.In Serial cable 4 pairs of cables are their, 2 pairs for Transmitting and 2 pairs for Receiving the Data. If you use serial cable to connect 2 computers, Conflict will happen while sending and receiving the data. In cross cable 2 pairs of cable will be in a different order so conflict won't happen. So use Cross Cable while connecting 2 similar devices.
To computer 9 if addressed correctly
what are some types of generic usb hubs
Bridges send information (data) to the specified destination, whereas hubs and repeaters do not.
A cross-over cable is used to connect two computers together without the use of a connecting device, such as a switch or hub. When daisy-chaining hubs and switches, some older equipment has a special port called the up-link port. This port requires the use of a cross-over cable to add hubs to hubs, etc.
MDF stands for Main Distribution Frame and IDF stands for Independent Distribution Frame.The MDF is the main computer room for servers, hubs, routers, DSL's, etc. to reside. The IDF is a remote room or closet connected to the MDF by fiber optic cable. In the IDF you can expect to find hubs and patch panels.
you will need a crossover cable to do it. Just plug it in Gaurav Phade ------------------------------------------------------------------------------------------- You will need a crossover cable to connect hubs that have no uplink ports. However if the hubs have uplink ports you can get away with using a normal CAT5 ethernet cable. Some of the larger TP-Link hubs are usually designed so that every port on the hub can act as an uplink port! Regards Phillip Hurrell Cert IT & Comp (Open)
tpatch cable is also known as straight cable and mostly connected same devices or nodes. but on the other side cross cable is just different then patch and used to connect different devices. Hem Gurjar
It is needed because you need to reverse the signals of a transmit line to a receive signal line. This is what network connectivity devices do, such as hubs, switches, etc. If you aren't using a connection device then the cable has to do that job.
You Use a standard port on one device, and an unlink port on the other. after that connecte the standard Cat5 cable.
because it makes sense to use a straight cable, as they are two unlike devices.
Nowadays, a USB cable connection is commonly used.
Only if a hub has auto sensing ports. With auto sensing it will detect the upload cable and will make a crossover internally.
If there's a WAN port on your hub, use that (If your x-port hub actually has x+1 ports, chances are the extra port is actually a WAN port). Otherwise, you probably can't connect that hub to another hub using a standard patch cable and will need a crossover cable. Some hubs will allow you to switch a port between normal and WAN mode, however (I believe some Trendnet hubs have this feature?), so you might want to check first. This is usually a hardware feature - normal hubs usually are not advanced enough to contain software interfaces for a browser to interact with)
To link 2 computers you should have cross cable. Because Serial cable is user to connect 2 or more dissimilar devices. To connect 2 similar devices like computers, Hubs, Switches you should use Cross cable only.In Serial cable 4 pairs of cables are their, 2 pairs for Transmitting and 2 pairs for Receiving the Data. If you use serial cable to connect 2 computers, Conflict will happen while sending and receiving the data. In cross cable 2 pairs of cable will be in a different order so conflict won't happen. So use Cross Cable while connecting 2 similar devices.
PC to Router = Ethernet Cross-OverBoth of these devices are expecting to connect to a switch. When connecting them together, we need to use a cross-over cable so that the transmit pair from 1 device, goes to the receiving pair of the other device.