3core*400mm2 xlpe cable
It depends on what kind of hub you mean. Some useful cables could be power cables, CAT 5e cables, fiber optic cables, etc.
An mgg cable is an cable that you use when you need to find personal stuff about you online.
Cable tester
The two basic types of cables are power cables and data cables. Early PCs used a ribbon cable to connect both hard drives and floppy. Later the Hard drive cable was changed from 40 wires on 40 pin to 80 wires on 40 pins. The additional wires were grounds between each data carrier. Newer computers use a smaller serial ATA (SATA) cable that uses 7 individual wires - 4 data wires and 3 ground wires. Other data cables and connectors usually use a flat ribbon cable for connections in the case. Examples are the serial ports, parallel ports, USB ports. The early PC had few connections sold with it, and we used to use a multi-purpose card to add ports and memory capability. Since the card was overcrowded, an extra "back plane connector" was included to give you a place hook up your printer of modem. It connected with a ribbon cable and a "header" block that plugged onto pins on the multi card. The power connectors on the early PC power supply were round and a keyed header attached them to the motherboard. Newer Motherboards often have an auxiliary power connector that enhances the distribution of power to the motherboard. This is only a benefit if the computer power supply has isolated rails for the different voltage supplies, or if the board must use more current than the other wires can safely carry. Hard drives and floppy all used the same size 4 pin Molex connector. The mini power connector arrived with the smaller floppy. The new SATA drives use a special power connector. New video cards that are high performance usually include one or more power headers requiring a feed just for the video card, and possibly it's fan. Early fans for the computers piggy backed across the power connectors going to the disk drives. More modern designs have dedicated sockets on the motherboard to allow reading the fan speed or better yet, controlling the fan speed. Some mother boards allow the control of "case fans". The power and sensor wiring for these fans is a 3 conductor cable, and some use a fourth conductor as a control line.
I could be wrong, but I believe you are talking about an HDMI cable. Between the antenna and the TV set use RG6 cable.
If you are referring to the main battery cable use 00 guage cable.
You can use 120v 10a 125w cable projectors 110-240v power in India.
One power connector is for the SATA power cable and the other is for the standard power cable. Use one or the other depending on what power connectors you have available in your system but not both.
You will use a power supply cable to get power to the Xbox 360. You can use several cables to connect the Xbox 360 to TV. The most popular cable to use to a HDMI, this will give you the best 1080p picture (if you TV supports it). The original cables to connect xbox to tv is RWY cable.
The main thing is that you use fan over processor and for the CPU body.The CPU Cabinet should be well aerated.Do not connect wires in the wrong port.Do not use defective devices.Use the power cable of same specifications that of the requirements of electricity for motherboard.
That is the main use, to fuel nuclear power plants
To plug in your PS3 attach the power cable to the back of the PS3. Then Plug the other end of the power cable into the Electrical socket. Finally connect the output cable to your PS3 and to your TV. Your PS3 is now plugged in and ready to use.
investigative powers
To repair the power take off cable on a lawn chief riding mower 455 you will need to gain access to the motor. The power take off cable will be there. Once you have access to the cable you can remove it and replace it with a new one. It is best to use the owners manual that came with the power for the exact instructions.
disconnect all power. unplug all electrical cables from the back of the computer and press the power button. Remove the rear or side of the computer to see the inside. Locate the cd drive. Unplug the CD-ROM unit's cable from the main system board. The connection can be a thin ribbon-like cable with a bar-shaped connector that plugs into the rear of the CD-ROM unit. The cable may look like a small tube-like cable, as well. Take the power cable from the back of the CD-ROM. Use a screwdriver to remove any screws. Slide the cd- drive out and put the new one in the same place. attach the existing cables and plug the power cable in. reattach the rear or side computer panel and return the power.
Power Line ethernet is a network adapter, It connects to an electrical component in one room but allows for another room to use the power without having to connect to the main source through an ethernet cable. By doing this, it cuts down on many cables having to be run from the main electrical source to users of that source.
To replace the auger cable on the MTD snow blower, you have to disconnect it from power. Use a screw driver to open the screw and replace the auger cable in question.