0
privileged EXEC
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What router prompt can you use the router rip command?
On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.
Which command sequence will permit access to five router virtual terminal lines with a password of cisco?
router>enable router#configure terminal router(config)#line vty 0 4 router(config-line)#password cisco router(config-line)#login to configure router with telnet you must set up password or secret for privilieged mode.
A router has a valid operating system and config stored in nvram when the router boots up which mode will display?
user exec mode
Can you use a wireless router transmitter as a receiver?
If your router has a bridge mode then yes.
What are router modes?
#Configure terminal for configuration mode #exit for previous mode #ctrl+z for set up mode
Which router mode is accessed by entering the enable command?
privileged EXEC
What router prompt can you use the router rip command?
On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.
What is the command used to get into global configuration mode on a cisco router?
On user exec mode type enable. When inside the privilege mode type configure terminal. You will then be sitting into global config after this. Please see below example: Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
What command is used to enter the routers privileged mode?
enable after the Router> prompt
Which router configuration mode will require user authentification if an administrator issues the enable secret command?
It is the privilege mode.
Which router configuration mode will require user authentication if an administrator issues the enable secret command?
privileged executive mode
Which router CLI mode will require user authentication if an administrator issues the enable secret command?
It is the privilege mode.
Which names correctly identify the CLI mode represented by the prompt for Switch-East4?
line configuration mode user executive mode * global configuration mode privileged executive mode interface configuration mode * enable mode8 What command is used to change the default router name to Fontana? Router# name Fontana Router# hostname Fontana Router(config)# name Fontana * Router(config)# hostname Fontan
How do you setup router passwod?
there are 4 types of password used in router 1. previlage password 2. vty 3. console 4 auxilary on the router goto globle configuration mode type: router(config)#enable password [password] (for normal) router(config)#enable secret [password] (for encrypt password) router(config)#exit router(config)#ctrl+z (to save) it is used to set password in previlage mode
What prompt should a technician see when entering the hostname command for a router?
from the global configuration mode
How do you put sound on safe mode?
To enable sound in safe mode, one should enable both the audio and plug & play services. These settings can be accessed by typing 'services. MSc' into the run dialogue box and pressing enter.
Starting at the enable mode prompt what commands would you type to configure IP address 192.168.1.1 on interface E0?
I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#
