answersLogoWhite

0

What else can I help you with?

Related Questions

What would cause the toilet to make a loud high pitched sound when flushed?

On a syphon type, the diaphragm will scream if perforated or cracked. Depending on which system you have fitted, this could be anything from the ball valve to the flap valve and all points between.Below are instructions to change something completely. If you recognise what system the contributor is referring to all is well. For the rest of us it makes little sense.Explanation of a repair to an unspecified flush systemI don't know why but follow these instructions EXACTLY to fix it.Turn off the water supply to the toilet. Follow the hose attached to the bottom of the toilet tank to the cut-off valve. Turn this valve clockwise to turn off the water. Empty the tank by flushing the toilet, then dry out the toilet tank using old towels or a sponge. Place a bucket under the toilet tank to catch any water that is still in the tank.Unscrew the nut holding the hose to the bottom of the tank with vice grips or channel locks.Remove the nut screwed on to the toilet pump. This is under the toilet tank. After you loosen this nut, you may need to hold the toilet pump with one hand while removing the nut with the other because the toilet pump may turn with the nut.Remove the clip attached to the refill tube from the overflow pipe. Remove the toilet pump from the toilet tank.Attach the refill tube that came with your replacement toilet pump to the new toilet pump. Slide one end of the refill tube over the nipple on the toilet pump to cover the nipple completely. Attach the angle adapter to the other end of the refill tube.Place one of the shank washers that came with your replacement toilet pump on the threaded shank of the new toilet pump. Place the threaded shank into the hole in the bottom of the toilet tank.Fit the other shank washer over the threaded shank and push the washer firmly against the toilet tank.Replace the nut on the threaded shank of the toilet pump and tighten fully.Clip the refill tube to the overflow pipe using the angle attachment provided.Screw the water supply hose tightly onto the threaded shank. Turn the water supply back on and check for leaks. If water leaks from around the new toilet pump, check to make sure both shank washers are firmly in place and tighten both nuts fully.


Why does toilet bowl fill lower than previous waterline?

If the toilet bowl fills lower than the previous waterline, the tank may not be working properly. Check that the float is moving freely and allowing the tank to refill all the way. Also make sure the filler tube is filling the toilet and is not directed elsewhere.


Why is my toilet running all night and how can I fix it?

Your toilet may be running all night due to a faulty flapper or fill valve. To fix it, you can try adjusting the chain on the flapper or replacing the flapper or fill valve if necessary.


How can I deflate a tube effectively?

To deflate a tube effectively, first locate the valve on the tube. Press down on the valve to release the air. You can use a tool like a valve core remover to help release the air more quickly. Make sure to press down on the valve until all the air is released from the tube.


Why would the toilet not empty all water from the bowl when flushed?

It sounds like you need a new ballcock valve or either your fill tube has come off your flush valve. Just take tank lid off and check to see if water is going down the tube in middle of tank.


What are the steps involved in toilet water supply valve replacement?

To replace a toilet water supply valve, follow these steps: Shut off the water supply to the toilet. Drain the water from the toilet tank and bowl. Disconnect the water supply line from the old valve. Remove the old valve from the toilet. Install the new water supply valve. Reconnect the water supply line. Turn on the water supply and check for leaks. Make sure to follow all safety precautions and consult a professional if needed.


How can I deflate an inner tube?

To deflate an inner tube, first locate the valve stem on the tube. Press down on the valve stem to release the air. You can also use a tool like a valve core remover to deflate the tube more quickly. Make sure to remove all the air before storing or repairing the inner tube.


How do you properly deflate an inner tube?

To properly deflate an inner tube, first locate the valve stem on the tube. Press down on the valve stem to release the air. You can use a tool like a valve core remover to help deflate the tube more quickly and completely. Make sure to remove all the air from the tube before storing or disposing of it.


When I turned on valve to toilet after being off for a while no water is filling the tank?

Make sure your main water is turned on by turning on another sink or bath and if it is then turn your toilet valve off and on a couple times and see if any water comes out in your tank. If still no water is filling the tank then shut off the valve and take the supply tube off the valve and turn the valve on slowly to see if you have any water comming out. If still no water then your valve is plugged or your pipe to the valve is plugged which then you would need to clean out your valve or lines with the whole house water shut off. Sometimes I have seen that the plug is in between the valve an supply pipe connection and as soon i take the supply pipe off and turn on the valve it works just fine even when I put the supply pipe back to the toilet. I don't think it would be in your fill valve in your toilet tank unless you have pressure assist tanks and with them all you need to do is take out the screen inside them.


How do you change the expansion valve on a 1996 Geo Prizm?

You'll have to discharge the system then raise the car and put it on jack-stands. You've got two fittings on it, you hold the stationary one and loosen the other fitting. Once you separate the pipe, you'll have to use a pair of needle nose pliers to pull the orifice tube(expansion valve) out of the tube. Put in your new one, put it all back together and refill the system. Do not listen to the answer above it is wrong answer. An orfice tube is not the same as the expansion valve. An expansion valve is a block valve so therefore you cannot take a pair of needle nose pliers to pull it out. The expansion valve is in a box where the eveporator and heater box. In order to change it you need to pull it out under the dash(passengers side) then put it all back together.


What is a Sloan Valve used for?

A Sloan Valve is used primarily on toilets. The Sloan Valve is the device that allows one's toilet to flush normally and properly, releasing all of the water at once.


Why would it be necessary to refit a valve when a toilet is broken?

If the toilet is not running right, won't stop running, or not running at all, it could very well be the fill valve. This means that the valve will need to be replaced as soon as possible or the toilet will not work properly. If not replaced (or refitted), it could start to leak and end up costing one even more money in the long run.