answersLogoWhite

0

I had the same question, but answered it myself. You push, and hold the center of the three buttons on the back of the main (not remote) unit, until you hear a "beep." This will cause an icon on the front to begin flashing. Sit the remote unit right next to the main unit, and wait a couple of minutes. Eventually, the unit will automatically program and you're ready to go.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Instruction manual for envirastation model DWS-210?

envirastation dws-210 instructions


How to set your Envirastation DWS-220?

Your Envirastation DWS-2220 will set itself. It is recommended that you install the home receiver near a window and away from metallic objects.


How do you set an Envirastation dws-220?

My Manual for 220 gives Contact 1 800 466 3342 Contact Envirastation Customer Relations Service dept 168 3000 Pontiac Trail Commerce Township, Mi 48390 cservice@envirastation,com


Instructions for Envirastation dws-200?

I think I solved the problem of programing the EnviraStation DWS-200. To keep the settings from reverting to the setting you are trying to change, press the 'set' button one more time after you have gone through all the settings.ie, you start by pressing 'set' and holding it down for 3 seconds.that brings up the 12/24 hour choice, press set again to get to the hour.Adjust the hour with the + & - buttons on the back, then press set to advance to minutes.continue through to the year month and day settings and when all is done,PRESS SET ONE MORE TIME.Anyway after a couple of hours looking for information and always having it revert to thetime I was trying to change, I finally found some instructions for the DWS-220, which is set from an atomic clock, but there were instructions for manual setting, it was there that I saw the information about that last push on the set button. It's worth a try.


How do you change to Centigrades on EnviraStation?

To change the temperature unit on an EnviraStation to Celsius, locate the settings menu on the device, and look for an option to change the temperature unit from Fahrenheit to Celsius. Follow the on-screen instructions to select Celsius as the preferred unit of temperature measurement.


How do you set your Envirastation DWS 220?

To set your Envirastation DWS 220, first ensure it is properly connected to a power source and any necessary sensors. Use the control panel to navigate through the settings, adjusting parameters such as water quality thresholds and alerts as needed. Refer to the user manual for specific instructions on calibration and configuration to tailor the device to your local environmental conditions. Finally, regularly monitor the readings to ensure optimal performance.


How do you stop your envirastation dws 220 from beeping?

To stop your Envirastation DWS 220 from beeping, check for any alerts or notifications on the device that may require your attention, such as low battery or maintenance needs. Often, pressing the reset button or turning the device off and back on can resolve the issue. If the beeping persists, consult the user manual for specific instructions or troubleshooting steps related to your model.


How do you clear the alarm settings on an EnviraStation DWS-170?

To clear the alarm settings on an EnviraStation DWS-170, navigate to the alarm settings menu using the device's interface. From there, you can select the specific alarm you wish to clear and confirm the action to reset it. If needed, refer to the user manual for detailed instructions specific to your model. Finally, ensure to save any changes before exiting the menu.


What set of instructions tell the computer what to do?

A program is a set of instructions that tell a computer what to do. In the computer, those instructions are called opcodes and make up an instruction set.


What is usually a set of instructions for making a particular protein?

This set of instructions is called a gene.


What is the term for instructions that tell a computer what to do?

The instructions for a computer are called programs.


What is a set of instructions called?

Set of instructions is called a PROGRAM. And set of program is called a SOFTWARE.