answersLogoWhite

0

for an ordinary straight handrail start by measuring up from the edge of the top tread 34 inches and make a mark. do the the same at the bottom tread and then connect the marks with a chalk line if wall is unfinished or if you are going to paint the wall after rail is installed. if its a finished wall then use a string tightly stretched between two nails. this line will be the bottom of the handrail. locate the exact centerline of studs at top and bottom and roughly at 32 inch spacing in between. locate studs using a stud locator [cheap at lowes or Home Depot] or tap wall gently with a hammer and you will hear a distinct solid sound when you are tapping directly over a stud. then use a very small finish nail to pierce the wall and locate the exact center of the stud. once you locate one centerline usually the rest will be 16 inches on center which will save you a lot of time. using a small level make a very faint vertical line at your centerline mark. then position your bracket by sighting across the top of the bracket to your string line and make pencil marks in the bracket screw holes. predrill screw holes or use 2 inch drywall screws to make predrilled holes. at this point you should have top and bottom and roughly 32 inch between bracket holes. make sure your top bracket is back beyond the leading edge of top tread by at least 6 inches and bottom bracket is the same beyond the edge of the tread. if no studs at these points use heavy duty wall anchors. measure your handrail about 4 inches beyond top and bottom brackets and install predrilling the holes into the bottom of the rail. if you want a slightly fancier look cut the handrail on a 22 and a half angle top and bottom and a piece to return to the wall cut on a 45 angle on the end to the wall and a 22 and a half angle on the end that meets the rail. use construction glue on the wall end and the end of the handrail[just a little. before cutting main rail or end pieces cut test pieces and position first so when you cut the final pieces you know what you,re doing. remember --measure two or three times and use test pieces first. it,s easy if you just take your time and enjoy what you,re doing. lots of luck! How to Measure for your Handrail or Railings These measurements enable us to determine the angle of your stair railing or your wall mount handrail. How to Measure Linear Feet

Pricing: by linear feet: The linear feet are found by determining how long the railing will be. The cap rail is the top section of the railing which is grasped by your hand as you climb or descend. The portion of the cap rail that curves down into the endings is not included in this measurement. IMPORTANT! For handrail, mounted to the wall on a staircase, we need to know on which side of the stairs the handrail is to be mounted when you are looking up the stairs. If stair rail is to be fastened to a wall as well as to the steps, we will need precise measurements.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How can I install a handrail on concrete steps?

To install a handrail on concrete steps, you will need to drill holes into the concrete, insert anchor bolts, and secure the handrail brackets to the bolts. Then, attach the handrail to the brackets using screws or bolts. Make sure to use a level to ensure the handrail is straight and secure.


What is the total labor cost to install a handrail?

The total labor cost to install a handrail depends on factors such as the complexity of the installation, location, and hourly rates of the workers. It is recommended to obtain quotes from contractors to get an accurate estimate.


How do you install an outdoor handrail?

To install a hand rail, you will need to buy a kit. You will also need screws and a screwdriver or an electric drill to install the hardware.


Which side do you install a handrail?

Which ever side is 18" to the center of the commode.


What is the cost to install a handrail in a residential property?

The cost to install a handrail in a residential property can vary depending on factors such as the material, length, and complexity of the installation. On average, homeowners can expect to pay between 200 to 600 for a basic handrail installation. However, this cost can increase if additional features or customization are required. It is recommended to obtain quotes from multiple contractors to get an accurate estimate for your specific project.


What are the types of handrail?

what is a type B handrail


What is a nonstandard handrail?

This probably refers to a handrail that doesn't meet with the current building code standards.


How do I install stair balusters?

To install stair balusters, first measure the spacing between each baluster and mark the placement on the stairs. Then, drill holes in the stairs and handrail for the balusters to fit into. Finally, secure the balusters in place using screws or adhesive.


What is the average height of a handrail?

The average height of a handrail is typically between 34 to 38 inches above the surface it is mounted on.


What are the recommended specifications for a 2x4 handrail in a residential staircase?

The recommended specifications for a 2x4 handrail in a residential staircase are typically a height of 34-38 inches above the stairs, with a distance of 1.5 inches between the handrail and the wall. The handrail should be sturdy and able to support weight, with smooth edges to prevent injury.


What is the standard height for a stair handrail and how high should a stair handrail be according to building codes and regulations?

The standard height for a stair handrail is typically around 34 to 38 inches above the stairs. Building codes and regulations usually require the handrail to be at least 34 inches high to ensure safety and accessibility.


What is a handrail post called?

The post actually is the banister. The fat bit that you slide your hand on is called a handrail or a balustrade.