0
If you have a 2-prong 240V outlet and only 2 wires and every wire is connected to two separate 20A breakers how can you replace it for one 120V outlet without rewiring?
Asking this type of question usually means you aren't ready to do this yourself.
If you get any detailed "how to do it" answer here, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.
<><><>
(LIFE SAFETY WARNING! [disclaimer]
Electricity is dangerous!
You can be injured or killed!
Improper installations can cause fire, injury and death!
Should you be doing this yourself?)
This is one of those questions - if you know this little, you shouldn't be doing what you are planning...
No disrespect intended, but this is SO basic that it suggests you have not studied the subject at all ...and you obviously don't have enough experience to do this safely!
Electricity is dangerous!
You can be injured or killed!
Call an electrician!
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
If you do this work yourself, always turn off the power
at the breaker box/fuse panel BEFORE you attempt to do any work AND
always use an electrician's test meter having metal-tipped probes
(not a simple proximity voltage indicator)
to insure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS
WORK SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
Can you replace double pole with two single poles?
Yes, you can replace a double-pole circuit breaker with two single-pole circuit breakers if they are connected to separate circuits. It's important to ensure that both single-pole breakers have the appropriate ampacity and are properly installed according to electrical code.
Can you use a 100 instead 20 to change breakers?
To replace breakers in an electrical box it is extremely important the replace the breaker with the same wattage. Do not replace a 100 breaker with a 20 breaker is can cause damage.
Is it possible to convert 220 v wiring to two 110 v wiring?
You will need a 220 volt primary isolation transformer with a split, center taped, secondary 220 volt winding.-------------------Answer for USAIf you live in the United States and your 220v circuit is a 2-pole circuit, you replace the 2-pole breaker with 2 individual 110v breakers and **PRESTO** you are now ready to run 2 individual 110v circuits.If you wish to use existing wiring, and you have 3 wires plus ground, you have all you need. These 2 circuits can share the same neutral without any electrical danger.Before you do any work yourselfon circuits, equipment or appliances,ensure the circuit is, in fact, OFF.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Do breakers on a fuse box ever go bad?
Yes, but they are easy to replace.
Do GFCI breakers go bad over time?
Yes, GFCI breakers can go bad over time due to wear and tear, electrical surges, or other factors. It is recommended to test GFCI breakers regularly and replace them if they are not functioning properly.
When did circuit breakers replace fuses in homes?
Circuit breakers started replacing fuses in homes in the 1960s and 1970s as a safer alternative for protecting electrical circuits. Circuit breakers are more convenient as they can be reset, whereas fuses need to be replaced when they blow.
What breakers will work with gould box?
Some Siemens may work but remember you are responsible for any fire or lives lost that may occur from using the wrong breaker. Get Gould breakers and you will then know they are safe. Can't find Gould breakers then replace the entire service panel. That is what I would do.
How do you replace fuel pump and sending unit?
you have to remove the fuel pump it is connected to it, it has to be replace as one unit
What are the recommended steps for replacing Stab Lok replacement breakers in a circuit breaker panel?
To replace Stab Lok replacement breakers in a circuit breaker panel, follow these steps: Turn off the main power supply to the panel. Identify the Stab Lok breakers that need to be replaced. Carefully remove the old breakers by disconnecting the wires and pulling them out. Insert the new Stab Lok replacement breakers into the panel. Reconnect the wires to the new breakers, ensuring they are securely attached. Turn the main power supply back on and test the new breakers to ensure they are functioning properly. It is important to follow safety precautions and consult a professional if you are unsure about any step in the process.
What are the advantages of using slimline circuit breakers in residential electrical systems?
Slimline circuit breakers offer several advantages in residential electrical systems. They are more compact than traditional breakers, allowing for more circuits in a smaller space. They also provide better protection against overloads and short circuits, helping to prevent electrical fires. Additionally, slimline breakers are easier to install and replace, making maintenance simpler for homeowners.
Will a 1989 4 liter jeep engine interchange with a 1993 4 liter HO engine?
Yes. However make sure you replace the HO transmission as well. There may also be some rewiring that will need to be done as well. Also, replace the U-joints on the drive line for the upgrade.
How do you reset circuit breakers in a Chrysler 1999 300M?
To reset the circuit breakers in a Chrysler 1999 300M, locate the fuse box inside the car or under the hood. Identify the circuit breaker that needs to be reset and push the reset button if available, or replace the breaker if necessary. Make sure to consult your vehicle's manual for specific instructions.
