answersLogoWhite

0

Program control Interrupt:-Program interrupt can be described as a transfer of program control form a currently running program to another service program on a request generated externally or internally. After the service program is executed the control returns to the original program. It is imperative for the CPU to return to the same state that it was when interrupt occurred after the program interrupted and the service routine has been executed. The state of the CPU at the end of the executive cycle(when the interrupt is recognized )is determined from:1. The content of the program counter. 2. The content of all processor registers. 3. The content of certain status conditions.Interrupts can be classified into the major types as below:-1. External interrupts:- this is come from input output devices, from a timing device, from a circuit monitoring the power supply, or from any other external source. 2. Internal Interrupts:- this is arise when an instruction or data is used illegally or erroneously. These interrupts are also known as traps. 3.Software interrupts:-external and internal interrupts r occur in the hardware of the CPU. A software interrupt is initiated during execution of an instruction. Software interrupts is a special call instruction that behaves like an interrupt rather than a subroutine call. It can be called to function by the programmer to intitiate an interrupt procedure at any desired pointing the program.

Reagrds

Raj Choudhary (kajla 9950645563)

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Difference between programmed IO and interrupt IO?

1.Programmed IO is the process of IO instruction written in computer program , where Interrupt Initiated IO is done by using interrupt and some special command. 2.The advantage of Interrupt Initiated IO is ,it is a time consuming process than Programmed IO. 3.In Programmed IO technique to transfer data,required constant motoring on peripheral by CPU,once data transfer is initiated, CPU have to wait for next transfer. In Interrupt Initiated IO once data transfer initiated ,CPU execute next program without wasting time and the interface keep monitoring the device. When the interface determines that the device is ready to transfer data, it generate an interrupt request,CPU stop the current task,execute the transferring process,and then return to the previous on-processing task.


HOW IS SOFTWARE INTERRUPT INITIATED?

Interrupt signals initiated by programs are called software interrupts. A software interrupt is also called a trap or anexception. A signal informing a program that an event has occurred. When a program receives an interrupt signal, it takes a specified action (which can be to ignore the signal). Interrupt signals can cause a program to suspend itself temporarily to service the interrupt. Interrupt signals can come from a variety of sources. For example, every keystroke generates an interrupt signal. Interrupts can also be generated by other devices, such as a printer , to indicate that some event has occurred. PCs support 256 types of software interrupts and 15 hardware interrupts. Each type of software interrupt is associated with an interrupt handler -- a routine that takes control when the interrupt occurs. For example, when you press a key on your keyboard, this triggers a specific interrupt handler. The complete list of interrupts and associated interrupt handlers is stored in a table called the interrupt vector table , which resides in the first 1 K of addressable memory.


Difference between harware interrupt and internal interrupt?

A hardware interrupt is initiated from a hardware event, such as a byte received from a serial port. It is asynchronous to the running program, i.e. it can occur at any time. An internal, or software, interrupt is initiated by the running program, thus it is under the control of the running program. In the 8085, for instance, the RST instructions are software interrupts. Note, however, that external interrupts can initiate a software RST instruction, so the two events can appear to be the same kind of event. The biggest difference is the handling of the interrupt enable (IE) flag. In the hardware interrupt, the IE flag is turned off when processing the interrupt, and it is turned on right before the interrupt service routine executes the final return instruction. The software interrupt, on the other hand, has nothing to do with IE. As a result, the code must be able to tell the difference.


Which interrupt listed below will terminate your program and return control to debug?

INT 20


What is interrupt in architecture?

program interrupt is transfer program control from currently running program to a service program depends on internal or external generated request after execution of service program, program control will be returned to original program


What is an interrupt How are multiple interrupts dealt with?

An interrupt is a request to execute different code, initiated usually by a hardware condition such as data-ready or operation-complete, but also sometimes initiated by the running program. The processor saves its immediate state, IP and Flags, on the stack and loads a new IP value, effectively doing a CALL sequence to some interrupt service routine. The routine does whatever processing is required, and returns, restoring the running program. Under normal conditions, the interrupt response sequence disables further interrupts, so that recursive entry does not occur. The service routine reenables interrupts just before returning, so that pending or further interrupts can be processed. If multiple interrupt levels are to be supported, such as in the 8085, the interrupt service routine can set the interrupt mask, blocking the level in progress, and then reenable interrupts. This way, a second interrupt on a higher level can be processed while the first interrupt is being processed. On return, the lower level interrupt disables interrupts, restores the mask, and then reenables interrupts prior to return.


What is the exact difference between interrupt handling and exception handling?

interrupt handling is the process of handling a break or interrupt called by a program where as exception handling is for handling some exceptional conditions that'll occur when a program is running


Difference between internal and external interrupt?

internal interrupt is synchronous with the program while external interrupts are asynchronous.


What are the release dates for From the Earth to the Moon - 1998 We Interrupt This Program 1-8?

From the Earth to the Moon - 1998 We Interrupt This Program 1-8 was released on: USA: 26 April 1998


What are the differences between a trap and an interrupt?

Trap is actually a software generated interrupt caused either by an error (for example division by zero, invalid memory access etc.), or by an specific request by an operating system service generated by a user program. Trap is sometimes called Exception. The hardware or software can generate these interrupts. When the interrupt or trap occurs, the hardware therefore, transfer control to the operating system which first preserves the current state of the system by saving the current CPU registers contents and program counter's value. after this, the focus shifts to the determination of which type of interrupt has occured. For each type of interrupt, separate segmants of code in the operating system determine what action should be taken and thus the system keeps on functioning by executing coputational instruction, I/O instruction, torage instruction etc.


What is the difference between trap and interrupt?

Trap is actually a software generated interrupt caused either by an error (for example division by zero, invalid memory access etc.), or by an specific request by an operating system service generated by a user program. Trap is sometimes called Exception. The hardware or software can generate these interrupts. When the interrupt or trap occurs, the hardware therefore, transfer control to the operating system which first preserves the current state of the system by saving the current CPU registers contents and program counter's value. after this, the focus shifts to the determination of which type of interrupt has occured. For each type of interrupt, separate segmants of code in the operating system determine what action should be taken and thus the system keeps on functioning by executing coputational instruction, I/O instruction, torage instruction etc.


What is interrpt request lines?

these are the block of code which tell the OS that a specific interrupt has arrived or to send interrupt request to some particular task. Interrupt is to stop the normal execution of the program and process the interrupt first according to it's priority in the interrupt vector table.