0
9600 baud refers to a data transmission speed of 9600 bits per second. It is a common rate used in serial communication, particularly in applications like modems and microcontrollers. At this speed, each second, 9600 bits of data can be transmitted, allowing for efficient data exchange in various electronic devices. The baud rate is often used to set communication parameters for devices to ensure they can send and receive data correctly.
What else can I help you with?
What would the time be at 9600 baud?
At 9600 baud, each baud represents one signal change per second. Since one baud corresponds to one bit, 9600 baud means 9600 bits are transmitted per second. Therefore, the time to transmit a single bit is approximately 1/9600 seconds, or about 104 microseconds. To calculate the time for a specific number of bits, simply divide the number of bits by 9600.
Is cable modem a broadband communication type?
Yes - generally speaking - anything above 9600 baud is considered "broadband" - becasue 9600 baud is as fast as federal law allows - by the old standard. Cable is usually at least 2,400,000 baud or 2.4 gig - depending upon your carrier and their pricing.
What baud rate needs to be configured on terminal emulation software to allow a connection to the console port of a router?
The default speed is 9600.
What band rate needs in terminal emulation software?
Its not band rate but its baud rate and it should be 9600 in the terminal emulation software to work with cisco devices.
Why you use 11.0592mhz crystal in place of 12mhz in 89c51?
The 11.0592 MHz crystal is commonly used with the 89C51 microcontroller because it provides an exact frequency that allows for accurate baud rate generation for serial communication. This frequency is particularly useful as it enables the generation of standard baud rates such as 9600, 19200, and 115200 baud without introducing timing errors. In contrast, a 12 MHz crystal would not yield the same precision for these common baud rates, leading to potential communication issues. Thus, the 11.0592 MHz crystal is preferred for reliable serial communication.
How much is 4.95 percent of 9600?
4.95 percent of 9600 = 475.24.95% of 9600= 0.0495 *9600= 475.2
What baud rates are supported by the USB to Serial Cable?
It supports from 300 baud to 1M baud.
What is 16.2 percent of 9600?
16.2% of 9600 = 9600*16.2/100 = 1555.2
Can't retrieve codes on obdII gmc sierra with a scanner?
2 things 1. port assignment and 2. baud rate............. usually port 3 and usually low baud like under 9600 or 4800 I forget cause mine is all set up and works on my sierra. initial setup sequence is important like cable to box to cable to port. proper sequence is on net
When was Frédéric Baud born?
Frédéric Baud was born in 1975.
Data rate of a channel?
A signal's data rate is often confused with its baud rate rate. The two are closely linked but are not identical. The data rate is a measure of how many bytes or bits of data can be sent per second. The baud rate, on the other hand is a measure of how many physical bits are sent per second, including start and stop bits and other idle bits. The baud rate is therefore higher than the data bit rate. A typical asynchronous serial signal that runs at a rate of 9600 baud will carry ten bits for every byte of data sent. One bit is a start bit. Another is the stop bit and the remaining eight are the eight bits of data. The bit rate is actually 8/10 x 9600 = 7680 bits per second. Most transmission methods have an overhead that makes the data rate a little slower than the baud rate. In time critical applications, the difference between them can become significant.
What is time in sending the message BADF00D5 in hexa using serial transmitter?
The time taken to send the message "BADF00D5" in hexadecimal using a serial transmitter depends on the baud rate (bits per second) and the number of bits in each character. Each hexadecimal character is typically transmitted as 4 bits, and if you include start and stop bits, each character may take 10 bits total (1 start bit, 8 data bits, and 1 stop bit). For example, at a baud rate of 9600 bps, sending 8 characters would take approximately ( \frac{80 \text{ bits}}{9600 \text{ bps}} \approx 0.0083 ) seconds, or 8.3 milliseconds. Adjust the calculation based on the specific baud rate used.
