0
What else can I help you with?
When was Sami Essid born?
Sami Essid was born in 1968.
When was Habib Essid born?
Habib Essid was born on 1949-06-01.
Why should the ESSID broadcasting be disabling?
This makes your network more secure against intruders as they don't see youre ESSID such as "BTHub73" or "Sky29756". So unless the attackers allready know the ESSID they can't access it.
Should the essid or ssid broadcast option should be turned off at the access point Wireless Security standards bbp?
True
ESSID SSID should be turned of a the access point?
It's recommended to turn off ssid broadcast.
In accordance with the wireless security standards the essid ssid broadcast options should be turned off at the access point?
Yes, You don't want to broadcast your secure network.
The essid ssid broadcast option should be turned off at the access point?
It should be, it makes your router a little bit harder to find for people who should not use your router anyway.
You're working on a school district's 802.11g wlan within each school several access points serve students teachers and administrators so that users can move about the school with their laptops and no?
A. The Same ESSID Network+ Guide to Networks Fifth Edition, Chapter 8
In accordance with the Wireless Security Standards SSID broadcast option should be turned off at the access point?
True; Make sure that the ESSID/SSID broadcast option is turned off at the access point!
Why Wireshark is not decrypting the captured wpa file even i have correct password and essid?
I tried to capture a file where network using security as below:[WPA-PSK-CCMP-TKIP]i am trying to insert a WPA Pre-shared Key in wire shark preferences under the protocol of IEEE 802.11 but when i enter a correct key nothing happen anyway to identify and fix this problem?
Will a Verizon phone work with ATT?
It depends on the phone model, the sim card it has, and whether it needs to be and has been unlocked. Even if the technical issues are avoided, there is the possibility that a vendor will not allow a phone model not approved to join its network based on its serial number or ESSID. Contacting customer support may help if you reach someone symphatic or not aware of the restriction.
How can I connect to a wireless network using command line in Linux?
Connecting to wireless is a somewhat different beast than connecting to wired networks because there are several extra aspects to the connection. The following instructions will walk you through 1) making sure your drivers are correct, 2)Connecting to the AP, 3)Joining the IP network. First things first, make sure that you can turn on the wireless interface, which might be named wlan0, ath0, or some other convention. If you can, then you have properly installed wireless card drivers. If you can't, then you might have to install drivers, firmware, or both to get it working. ifconfig wlan0 up Next, the configuration of all the wireless configurations is done using the iwconfig command. Using that tool, you can enter the SSID, Access Point MAC address, etc. Usually specifying the SSID is sufficient. To see a list of available SSID's to connect to, use iwlist, then configure your interface like so: iwlist wlan0 scan <produces a list of various SSID's along with their Access Point, frequency, encryption type, etc.> iwconfig wlan0 essid "MyNetworkSSID" Check the current configuration of your interface like this: iwconfig wlan0 If your interface has joined with the access point, you will see all the configuration information here. Now, your network HOPEFULLY has some sort of encryption. For that, you will need to install wpa_supplicant. The configuration here can vary from one distribution to another, but basically it will store encrypted network keys for various SSID's. If you use encryption you will have to use it, but I'm not going to explain how to set it up as it may be different on your distribution. All of that just registers you with the Access Point. Now you can finally set your IP address either by setting it manually or obtaining it through DHCP. Manually: ifconfig wlan0 192.168.1.100 or by DHCP dhcpcd wlan0 or dhclient wlan0
