0
What type of computer uses a drum plastic toner and fuser to create a printed page?
A laser printer uses a drum, plastic toner, and fuser to create a printed page. The drum is charged with electricity to attract the toner, which is then transferred onto paper and fused using heat from the fuser. This process allows for high-quality, fast printing of documents.
What else can I help you with?
Does it ruin the fuser to run printed paper though a laser printer?
The printed paper would be treated as blank paper by the laser. Otherwise, preprinted forms, etc, couldn't be used - which they can!
Why do laser printers require ventilation?
Part of the printing process involves melting toner onto the paper in order for the printed image to be permanent. This is done by a component called the fuser. The fuser gets very hot, and needs the ventilation to cool down so it doesn't overheat.
When was Diego Fuser born?
Diego Fuser was born on 1968-11-11.
Where can a Laserjet 4100 Fuser be purchased?
You can purchase one on Quickship and it only costs $286.89. With the assembly it has the ablity to print up to 200,000 pages of whatever you need printed.
Do bubble jet printers use a fuser assembly?
no. There is no fuser in a Bubble Jet Printer.
What is fuser oil?
Dimethyoxysiloxane
What is the signs that a printer fuser is going bad?
To check for a faulty fuser assembly do the following. Open the clam shell cover of the printer. In the back of the printer is the fuser assembly unit. The green part of this unit on the back portion of the fuser will open.Remember the fuser runs at an extremely high temperature. Be sure you are touching felted portions of the unit only to avoid burns. Gently push the green rear portion of the fuser unit back. Turn the printer around and look through the back. Are there visible streaks or rips in the upper fuser roller? Are there any visible bubbles in the upper fixing roller?If any of these symptoms are present you will need to replace the fuser unit of the printer.
Where can you find information about 'Fuser'?
Fuser is a Unix command and requires some technical knowledge to fully understand. Information on Fuser is available from Wikipedia, The Geek Stuff or may be found in specialist magazines relating to Unix.
How long should laser printer fuser last?
How long does a fuser unit last in the copier, if you have a large number of copies to be run
What is error message c-fc24 on a konica minolta bizhub c280?
The error message c-fc24 on a Konica Minolta Bizhub C280 indicates a problem with the fuser unit, specifically related to the fuser temperature being outside the expected range. This could be due to a malfunction in the fuser assembly, a faulty thermistor, or issues with the power supply to the fuser. To resolve the issue, it's recommended to check the fuser for any obstructions, ensure proper connections, and consider replacing the fuser unit if necessary. If the problem persists, consulting a technician or the service manual may be required.
What is fault code F-35-1 on konica 7222?
Fault code F-35-1 on the Konica Minolta 7222 typically indicates a problem related to the fuser unit, specifically an issue with the fuser temperature or a malfunction in the fuser thermistor. This could result from a variety of causes, including a faulty fuser assembly, poor connections, or an issue with the printer's control board. To resolve the error, it's recommended to check the fuser unit for proper installation, inspect wiring, and potentially replace the fuser if necessary. Always refer to the service manual for detailed troubleshooting steps.
Can you print on pressure sensitive vinyl with a laser printer?
No -------------------------------- There's really no such thing as a definitive "No" or even "Yes" for an answer to this question. Your mileage may vary depending on the printer, it's toner composition, and fuser temperature. I've successfully laser printed onto colored signshop vinyl with a lexmark E330 desktop laser printer. The printer has a front feed and a rear straight through exit, this is important as the vinyl wants to curl when exiting the fuser. You just grab the hot vinyl sheet and lay it flat on a table and it will stay flat. The trick to fusing the toner solidly onto the vinyl is to create a blank 8.5x11 page in photoshop and re-run the sheet through the printer a few times after it's printed. This will run it through the hot fuser without adding anything to the page. After this the print won't come off unless you really try to scour it off. http://www.rippedsheets.com/faq/faq_24.htm
