answersLogoWhite

0

yes if the battery is the same voltage, wire should be used to do this.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you change light in 2006 Ford Fusion radio?

It's surface-mount LEDs. If you know how to solder, they're green PLCC2 LEDs.


Can a 3 volt battery light 5 leds?

It depend on what the rating voltage of the LEDs are.


Can a nokia bl-5j 3.7 volt battery be used to power LED's safetly and how?

A: It sure can but what is voltage iof the LEDS 3.2 V then you need to drop 3.7 to 3.2 v at ~20ma .5v / 0,02=27 ohms in series the LEDS are 1.8 you need 3.7- 1.8/.02= 100 ohms in series. The warning is the life of this setup is going to be short lived after the battery drain off the battery needs recharging if so it is better to supply the LEDS from the charger directly will last until the LEDS QUIT FUNCTIONING


How do you solder fly leads to LEDs?

Use a heat sink. Many LEDs are heat sensitive. I make a heat sink by putting a rubber band round the handles of a small pair of snipe nosed pliers.


How do you fix a airsoft battery wire?

Solder the wire.


Trying to make some indicators for a bike and am going to use 1.5 volt leds and a 12 volt 11ah battery by putting 8 leds in series was wondering whether resistors are needed not to short the leds?

Resistors will be needed in all cases when driving LEDs from a voltage source, unless you are using LEDs that already have a built in current limiting IC inside the package (a few do these days, for example I have some blinking LEDs that need no resistor they have a blinker IC built in that also limits current).However you have another problem that you obviously are not aware of. 8 LEDs rated at 1.5V in series totals exactly 12V. But your battery is only rated at 12V. As the battery discharges its voltage slowly drops, the moment it drops under 12V all the LEDs will turn off! I strongly recommend that you use no more than 7 LEDs rated at 1.5V in a circuit powered by a 12V battery, so that the battery can actually gets a chance to discharge beyond its knee voltage. In this case the resistor will drop the remaining voltage, whatever it is depending on the charge state of your battery.


What is a battery clip used for?

A battery clip is used to connect a battery securely to a device or circuit by attaching to the battery terminals. It provides a convenient way to make and break the connection between the battery and the device without needing to solder the wires directly to the battery terminals.


How do I replace a burned out heated seat light in a 2001 Olds Aurora?

well if its anything like my 99' it is soldered in. i found out when i changed out my lights to blue leds. gonna have to solder a new on in!


Can rosin core solder work with leds?

Yes, rosin core solder can be used with LEDs, as it provides a good electrical connection while minimizing oxidation during the soldering process. However, care must be taken to avoid overheating the LED components, as excessive heat can damage them. It's best to use a soldering iron with a fine tip and work quickly to maintain the integrity of the LED. Additionally, ensure proper soldering technique to avoid cold joints.


Which is a more powerful light - 95 leds or 128 leds?

If your compairing apples to apples like 3 watt leds to 3w leds then 128. The more leds the higher the power.


Are LEDs dimmable?

Yes, LEDs are dimmable.


When to connect LEDs in parallel?

Basically, when LEDs are connected in parallel, the LEDs with the lowest resistance will be the brightest, the other LEDs will be dimly lit or not lit at all. Therefore, use LEDs with the same model number and colour.