answersLogoWhite

0

The Kenmore Gas Dryer will not heat and dry clothing.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How does a tumble dryer condenser box work?

A tumble dryer condenser box works by collecting the moisture extracted from the drying clothes. The hot air from the dryer passes through the condenser box, where the moisture is condensed into water droplets. The water is then collected in a reservoir or drained out, allowing the dry air to circulate back into the dryer.


How can I properly install a dryer vent box in my home?

To properly install a dryer vent box in your home, follow these steps: Choose a suitable location on the wall for the vent box, preferably near the dryer. Cut a hole in the wall that matches the size of the vent box. Insert the vent box into the hole and secure it in place using screws. Connect the dryer vent hose to the vent box, ensuring a tight seal. Test the dryer to ensure proper ventilation and make any necessary adjustments.


Can you wash a lunch box in the Wash and dryer?

Yes


Where is the Rough And Tumble Engineers Historical Association in Kinzers Pennsylvania located?

The address of the Rough And Tumble Engineers Historical Association is: Po Box 9, Kinzers, PA 17535-0009


How do you make a condenser in minecraft?

Place some collectors around your energy condenser, then open the condenser and place an item in the target box, then the number and the progress bar should increase once it gets to the required amount it will duplicate the item in the target box


Where is the AC condenser drain located on a 1988 Chevy Corvette?

The A/C condenser drain is located underneath the car toward the center of the vehicle. Just follow the outline of the condenser box, it should have a rubber nipple on it.


What is the best way to install a recessed dryer vent box in a 2x4 wall?

To install a recessed dryer vent box in a 2x4 wall, first, cut a hole in the drywall where you want the box to go. Next, insert the box into the wall cavity and secure it in place using screws. Connect the dryer vent hose to the box and seal any gaps with caulk or tape. Finally, replace the drywall and paint as needed.


What are five ways to move a box from one room to another?

# Slide # Carry # Throw # Tumble # Disassemble, reassemble


How do you wire a dryer plug to a breaker box?

To wire a dryer plug to a breaker box, you need to connect the wires from the dryer plug to the corresponding terminals in the breaker box. Make sure to follow the manufacturer's instructions and safety guidelines to ensure proper installation. It is recommended to hire a licensed electrician for this task to ensure it is done correctly and safely.


How can I properly install a dryer connection to the wall?

To properly install a dryer connection to the wall, follow these steps: Turn off the power to the dryer and unplug it. Locate the electrical outlet and ensure it is compatible with the dryer's plug. Install a proper outlet box and secure it to the wall. Connect the wires from the outlet box to the corresponding terminals on the dryer. Secure the dryer vent hose to the back of the dryer and the wall vent. Plug in the dryer and turn on the power to test the connection. It is recommended to consult a professional electrician if you are unsure about any step in the installation process.


Where is the double 30 amp breaker in an electric dryer?

It should be in the main circuit panel. If the dryer was added at some point there may be a separate box just for the dryer either beside the main panel or at the dryer plug. It is not in the dryer itself.


What are the necessary steps for installing a dryer receptacle box in a laundry room?

To install a dryer receptacle box in a laundry room, follow these steps: Turn off the power to the area where you will be working. Locate a suitable location for the receptacle box near the dryer. Cut a hole in the wall for the box using a drywall saw. Install the box securely in the wall. Connect the wiring to the receptacle according to the manufacturer's instructions. Secure the receptacle in the box and cover it with a faceplate. Turn the power back on and test the receptacle to ensure it is working properly.