answersLogoWhite

0

Had the same problem with my mighty mule gate opener. First thought the batteries or solar panels wasn't charged or charging ---and that's the spill the manufacturer threw out to me on the first go around---that wasn't the problem--but every time I called them --that's the spill they would start with over and over again solar panel and batteries. I took out the main board myself and exchanged it for another main board from the place I purchased it from (I had someone at the place I purchased the unit who allowed me to exchange the board out to check if the problem was with the main board --he must have known about the problem also) and then it worked for maybe two weeks with no problem then started doing the same thing again. Called the manufacturer about the problem again they basically refused to do anything about it on their dime, wanting me to pay to ship the whole unit back to them charging me to resolve faulty unit issue that they already knew about before placing the junk out into the market to be sold. The manufacturer knows and knew what is and was wrong with this piece of junk. They just don't want to own up to their faulty units and so who knows how many more people got stuck with the mighty mule piece of expensive junk. Maybe now they resolved that problem --don't know. I had purchased this unit several years back and almost right away the gate would do the same thing as your describing--- opening 2 inches and sometimes wouldn't even close or open. Pressing the button and nothing-- then maybe it would open. It was like a fickled person, "well, maybe I'll open the gate or maybe not". "maybe I'll open the gate just a little or maybe not" Very undependable piece of garbage.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

What is the default distance between tab stops?

One half inch


Eight foot gate how far apart do you place the posts for the gate?

Metal Gate & Posts: 96 inches plus 3 inches for barrel hinge plus 1 inch for clearance at non hinged post if hinge is mounted INSIDE between the posts. If a flat hinge is flat mounted on outside of post and gate, instead of 3 inches, use the width of the hinge ferrell (the raised ridge in the middle where the two sides of the hinge pivot).Wooden Gate & Posts: Same.If the hinges are mounted inside between the posts the above distances will let the gate swing 90 degrees or slightly less depending on the thickness of the post and the gate material. If you want to have gate swing a little further, either mount barrel hinges toward one side of the post or increase the hinge distance from 3 inches to a distance sufficient to permit the edge of the gate to clear the width of the post as it opens.


2007 jeep liberty rear door only opens one inch?

i thought youcould answer any question really!


2000 cavalier sunroof opens but does not close all the way Motor stops when the window is still open about an inch It's open more on one side than the other don't have money to fix doit youself tips?

Buy a hammer and some cardboard to cover the top, also don't forget the ductape.


How many turns does it take to shut an 18 inch gate valve?

The number of turns required to shut an 18-inch gate valve typically ranges from 3 to 8 full turns, depending on the valve's design and the specific manufacturer. Gate valves often have a rising or non-rising stem, which can also influence the number of turns needed. It's essential to consult the valve's specifications for accurate information.


What default tab stops will automatically be removed when a tab stop is set at 3 on the ruler?

The tab stops at half an inch, one inch, one and a half inch, two inches, two and a half inches and the new tab you set will replace the tab at three inches. So from the start of a line, pressing the tab key will go straight to the 3 inch tab mark.


What is the take off on 8 300 gate valve?

The take-off on an 8-inch 300 gate valve refers to the vertical distance from the bottom of the valve body to the centerline of the outlet port. Typically, for an 8-inch 300 lb gate valve, this measurement can vary slightly based on the manufacturer and design specifications, but it generally ranges from about 8 to 10 inches. It's important to consult the specific valve's technical data sheet for precise dimensions.


Why can you rotate crankshaft only 4 inch then it stops?

Its an auto lock, if you go more than 4 inches the crankshaft breaks


If my pubic hair stops you from seeing my penis should i trim it?

yes, yes i would say u should trim it... unless u got like a 1/2 inch dick or somethin XD but yah id say keep ur pubs 2 an inch or inch and a inch and a half MAX.


Default tab stops are set at?

They are at every half inch or 1.27 centimetres, depending on which measurement units you have active. Both values are equal.


How much iron stops a gun shot?

Depends entirely on the gunshot, and the type of "iron". One fourth of an inch of mild steel will stop a .22 pistol bullet, but larger rifle calibers may penetrate an inch.


What is the plug gap on an 88 mighty max 20 engine?

the gap is as follows; US .39 to .43 inch Canada .28 to .31 inch plug is a NGK BPR5ES-11, BP5ES-11 On Autolite Platinum - 63 plugs the gap is .44