0
The MH ballast will not have the ignitor required to power up the HPS bulb. I have 1000w ballast that can be switched between HPS and MH with a singe switch just by disabling the ignitor for the MH.
I would look into conversion bulbs, or else check out this site for $20 150w HPS ballast with bulb.
http://www.e-conolight.com/Product/EProductDetail.asp?ProductFamilyID=7&FGNumber=E-MT6H151G
If it doesnt appear, sellect vapor tights, then the 150hps.
What else can I help you with?
Can you use a 100 watt metal halide bulb in a 150 watt lamp?
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
When you need to use metal halide conversion bulb?
When you want to use a MH bulb in an HPS ballast you must use a conversion bulb. It must be the same wattage as the HPS bulb
Can you split 2 light using 1000w hps ballast?
No, a 1000w HPS ballast is designed to power one 1000w HPS light bulb. If you want to power two lights, you would need to use a ballast with enough power output for two lights, like a 2000w HPS ballast.
Can you use a 400W high pressure sodium bulb in a metal halide ballast?
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
How much wattage will the ballast and a 150 watt hps bulb use?
A ballast typically uses around 5-10 watts of power. In this case, a 150 watt HPS bulb will consume 150 watts of power when turned on. So, in total, the ballast and the bulb together will use around 155-160 watts.
Can you run 400watt mh in a 600 watt hps?
Yes, you can run a 400-watt metal halide (MH) bulb in a 600-watt high-pressure sodium (HPS) fixture, but you need to ensure that the ballast is compatible with the MH bulb. Using a 400-watt MH bulb in a 600-watt ballast may lead to reduced efficiency, as the ballast will deliver more power than the bulb requires. It's essential to check the ballast type and ensure that it can operate both bulb types safely. If not compatible, it's best to use the appropriate ballast for the MH bulb to avoid damaging the bulb or the fixture.
Can you use a hps bulb in a metal halide fixture?
In most cases a cfl bulb can be replaced with an incandescent bulb as long as the base matches. for an example: if a cfl bulb has a GU24 base an incandescent bulb will not work! Also, ensure the wattage of the bulb does not exceed manufacturers rating.
Can you use a 1000 watt hps without a ballast?
No, you cannot use a 1000 watt HPS (high-pressure sodium) lamp without a ballast. The ballast is essential for regulating the electrical current flowing through the lamp, which is necessary for it to operate properly and prevent damage. Trying to operate a 1000 watt HPS lamp without a ballast can result in the lamp not lighting up or malfunctioning.
Can a 400 watt high pressure sodium bulb be used in a 400 watt metal halide ballast?
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
How much wattage does a 250w HPS bulb use?
A 250W HPS (High-Pressure Sodium) bulb uses 250 Watts of electricity when it is operating at its full power. It is important to note that the actual power consumption may vary slightly due to factors such as ballast efficiency and voltage fluctuations.
Can you run a 50 watt halide bulb on a 100 watt halide ballast?
No, it is not recommended to run a 50 watt halide bulb on a 100 watt halide ballast. The ballast should match the wattage of the bulb to ensure proper operation and to avoid potential damage to the bulb and ballast. It is best to use a ballast that is rated for the wattage of the bulb being used.
Can you use a 70 watt high pressure sodium bulb in a 150 watt ballast?
No, you can not use a 150 watt high pressure sodium bulb with a 70 watt ballast.
