answersLogoWhite

0

What else can I help you with?

Related Questions

What is lozenge joint?

A riveted joint known as Lozengejoint used for roof, bridge work or girdersetc. In such a joint,*diamond riveting is employed so that thejoint is made of uniform strength.


What is the efficiency of riveted joint?

The efficiency of riveted joints is the ratio between the minimum strength of the joint against failure by tension, shear or bearing to that of the members without a joint .balamurugan.g


How do you produce a good hot rivet joint?

To produce a good hot rivet joint, first make sure the rivet and the parts to be joined are clean. Heat the rivet until it glows, then quickly insert it into the pre-drilled holes in the parts to be joined. Use a pneumatic riveting hammer to upset the tail of the rivet, creating a secure joint.


Riveting and welding?

Riveting - when a solid fastener is placed in a drilled hole and expanded to hold an object in place. Welding - when a thin wire ('filler') is melted along with the area of bonding on the workpieces, which form a joint when cooled.


What is the difference between riveting and spot welding?

A riveted joint with single rivet and a bolted connection with single bolt are perfect pin-joints. When number of rivets/ bolts along the axis of member increases, the degree of restriction to rotation gradually increases and becomes a rigid joint, which prevents rotation by offering moment reaction.


How do you change a upper passanger side ball joint on a 1994 Chevy silvarado 4x4?

if it is original the upper ball joint is riveted in, it will need to be chisel out,there are four rivets and then the nut that holds it to the control arm.new ball joint will come with bolts and nuts


What is the upper and lower ball joint connected to on a 1991 Chevy k1500?

The ball joints are riveted or pressed into the upper and lower control arms, then the spindle is bolted to the ball joints.


Why is welding used?

When two pieces of metal are joined by welding they become one as if they were made that way. Welding replaced riveting and reduced the amount of metal used while producing a stronger joint.


How can metals can be bejoined together using the riveting and brazing process?

In riveting, a rivet is inserted into drilled holes in the metals and then the ends are hammered to create a permanent joint. In brazing, a filler metal with a lower melting point is used to join two metals together by heating the assembly until the filler metal melts and forms a bond upon cooling.


How to Remove lower ball joint 70 cutlass?

use a pickle fork to bust it loose from the spindle and then they are usually pop riveted in place if they have never been changed, drill the pop rivets out and the ball joint is out, install the new ball joints with bolts and nuts.


How do you replace a lower front control arm bushing on a 1999 Mercury Cougar V6?

Go to AutoZone.com, They have on line repair manuals. The arm has two bolts to the frame and the ball joint has a pinch bolt to the steering knuckle. place a jack under the knuckle and jack it up a little, then pry ball joint out, unbolt frame bolts and pull it out. The bushings can now be replaced. I would replace the whole arm while its out, the ball joint is riveted in the frame Go to AutoZone.com, They have on line repair manuals. The arm has two bolts to the frame and the ball joint has a pinch bolt to the steering knuckle. place a jack under the knuckle and jack it up a little, then pry ball joint out, unbolt frame bolts and pull it out. The bushings can now be replaced. I would replace the whole arm while its out, the ball joint is riveted in the frame


How do you change a balljoint on a 1993 Mitsubishi 3000 gt?

I am not familiar with this car in particular but ball joints are either pressed in, bolted, or riveted into the control arms. On top of the ball joint is the steering knuckle, usually the ball joint is held into the steering knuckle with a pinch bolt. Which is easily removed. After the pinch bolt is removed you must force the control arm away from the steering knuckle which sometimes requires the use of an air hammer. Depending on what type of fit the control arm has with the ball joint, you will either need a special tool to press out the old ball joint and press in the new one, if the ball join is a press fit. Or if it is riveted you will have to carefully drill out the rivets and replace the new one with bolts. If it is bolted in you simply loosen the bolts and knock out the old ball joint. Installation is reverse.