0
If a fault occurs in an area where rock layers have been folded what type fault would it be?
What is the relative age of a fault that cuts across three horizontal sedimentary rock layers?
A. The fault is older than the middle layer. B.The fault is younger than all the layers it cuts across.
C. The fault is the same age as the top layer. D. The fault is older than all the layers it cuts across == ==
What else can I help you with?
If you wanted to know whether a certain mountain was formed by compression what would you look for?
To determine if a mountain was formed by compression, you would look for folded and faulted rock layers, as well as evidence of intense pressure causing rocks to deform. Additionally, you might find evidence of compression in the form of thrust faults or folded strata within the mountain. Lastly, examining the types of rocks and their orientation can also provide clues about the mountain's formation.
What is the cause of folded sedimentary rock layers?
Pressure from the sediments above compact the sediments down creating a rock. A fold would be the result of oh say allot of pressure. Sedimentary rocks a generally layered strait across so if it's folded it may be metamorphic. They form when igneous or sedimentary rocks are but under immense heat and pressure.
If you could observe only the land surface around a fault how could you tell if the fault is a strike-slip fault?
In a strike-slip fault, you would observe horizontal displacement along the fault line with minimal vertical movement. This can be seen through offset features on the land surface like roads, rivers, or ridges. Additionally, the orientation of linear features such as rock layers or fault scarps would be consistent with the direction of the fault movement.
When plate movement causes rocks to break what is is called?
actually convection is wrong the correct answer would be called faulting
What is the principle of within a sequence of undisturbed sedimentary rock the layers get younger going from bottom to top?
Yes. The only exceptions would be if tectonic forces either overturned the rock layers through folding or if older layers were thrust on top by a thurst fault. A thrust fault would be apparent if you see the same layers repeat.
How many layers would there be if you folded a piece of paper 7 times?
128
What layers of small sediments stick together because when pressure occurs?
When layers of small sediments stick together because of pressure, compaction occurs. :)
What type of unconformity would mark the boundary between older rock layers and th newly deposited rock layers?
The boundary between older rock layers and newly deposited rock layers is typically marked by a disconformity or an angular unconformity. A disconformity occurs when there is a gap in the geological record due to erosion or lack of deposition, with both layers being parallel. An angular unconformity, on the other hand, features older rock layers that have been tilted or folded before new layers are deposited on top at an angle. Both types indicate significant geological events that disrupt the continuity of sedimentary layers.
If you wanted to know whether a certain mountain was formed by compression what would you look for?
To determine if a mountain was formed by compression, you would look for folded and faulted rock layers, as well as evidence of intense pressure causing rocks to deform. Additionally, you might find evidence of compression in the form of thrust faults or folded strata within the mountain. Lastly, examining the types of rocks and their orientation can also provide clues about the mountain's formation.
What is the cause of folded sedimentary rock layers?
Pressure from the sediments above compact the sediments down creating a rock. A fold would be the result of oh say allot of pressure. Sedimentary rocks a generally layered strait across so if it's folded it may be metamorphic. They form when igneous or sedimentary rocks are but under immense heat and pressure.
If you could observe only the land surface around a fault how could you tell if the fault is a strike-slip fault?
In a strike-slip fault, you would observe horizontal displacement along the fault line with minimal vertical movement. This can be seen through offset features on the land surface like roads, rivers, or ridges. Additionally, the orientation of linear features such as rock layers or fault scarps would be consistent with the direction of the fault movement.
Which fault would be found on divergent boundary?
A normal fault is typically found on a divergent boundary. This type of fault occurs as the Earth's crust is being pulled apart, causing one side to move downward relative to the other.
How would you have know that the fault is the youngest feature in the rock body?
To determine that a fault is the youngest feature in a rock body, geologists use the principle of cross-cutting relationships, which states that a geological feature that cuts through another is younger than the feature it disrupts. If the fault displaces layers of rock, it indicates that the faulting occurred after those layers were formed. Additionally, examining the sedimentary layers for any evidence of erosion or deposition can further confirm the fault's relative youth compared to the surrounding rock formations.
Why would it be difficult to see your image in a folded piece of foil?
because it is folded
Why do sedimentary rock layers become folded and faulted as you move from west to east?
That would depend on the location on Earth that you were moving west to east along. The movement from west to east can be undertaken anywhere on Earth.
What happens if neutral wire goes in earthing hole?
That would be a ground-fault if it occurs anywhere other than inside the service panel.
How many circles would you find in a net that can be folded to form a cylinder *?
How many circles would you find in a net that can be folded to form a cylinder? *
