0
The SI unit for conductivity is the siemens per metre. Conductivity is the reciprocal of resistivity, whose SI unit is the ohm metre.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the effect of temperature on conductance?
If you're talking about electrical conductance of a wire, I think increased temp means decreased conductance. Because the metal atoms vibrate faster with increased temp, so the electrons collide with the atoms more frequently, therefore find it more difficult to get through the wire
What is specific conductance of 0.02 molar KCl solution?
1413 uS/cm
Is heat is measured in degrees Celsius?
Temperature is measured in celcius.Heat is measured in joules.
How is hail measured?
Its diameter and circumference are measured.
How are oceanic plated measured?
They are measured in seismic waves.
What is electrical onductance measured in?
Electrical conductance is the reciprocal of resistance and is measured in siemens (symbol: S).
What is the resistance in ohms of 400 siemens?
25 ohmsAnswerResistance is measured in ohms. Conductance is measured in siemens. Conductance is the reciprocal of resistance. So the ohmic equivalent of 400 siemens is 2.5 milliohms.
What is the conductance of a 10 ohm's resistor?
Conductance is the reciprocal of resistance, and is measured in siemens (S). So a 5.1 ohm resistor has 1/5.1 conductance, which is approximately 0.196 078 431 372 549 019 607 843 137 254 9 S.
Energy transfered as heat through a material is called?
Thermal Conductance, measured by [Watts/(meter x Kelvin)].
How does a multimeter mesure the amount of electrolytes in a drink?
Using an circuit involving a 9V battery and snap connector, a conductance sensor made of small plastic tubing and copper wire, and alligator clips, the conductance sensor is placed in the drink to be measured, and the electrolytes close the circuit. The multimeter can then read off the ampage you need to determine conductance using G = I/V, G being conductance in siemens, I being ampage, and V being voltage.
Why direct current has no conductance?
Direct current is measured in units of voltage and current. Conductance is the inverse of resistance. The two systems are not related to each other, except through Ohm's Law. The question does not make sense. Please restate the question, with more detail as to what you are trying to ask.
Why is conductance G?
Conductance is an opposition of Resistance and it is denoted by G. It is given by the relationship G = 1/R . In past the unit of conductance was (mho) which is opposite to (ohm). But these days the unit of conductance is Siemens which is denoted by 'S'.
Will a fully charged new battery have a low conductance reading?
No it will have high conductance
Why conductance is ignored in transmission lines?
Conductance is ignored in short circuit studies because the inductance of the line is the dominant value. Conductance may not be ignored in stability studies.
The si unit of conductance is?
The unit of electrical conductance is the mho.
What is the use of conductance?
When referring to electrical conductance, it is used in the application of electricity to equipment. Electrical conductance measures the equipment's ability to conduct electrical charge. A practical application would be to decrease the resistance in an electrical circuit so that the conductance is higher and electricity flows more smoothly.
What is effect of dilution on conductance?
The conductance of a given conductor, C = La/l ..(i)\ L = l/Ra ..(ii)The resistance is expressed in units of ohm, the conductance has units of ohm-1 or mho.The conductance of solutions is also governed by the same relations. From (i), if l = 1,a = 1, the specific conductance L = C. That is,the specific conductance (L) is the conductance of the solution enclosed between two electrodes of 1 sq. cm area and 1 cm apart. when you dilute the solution the concentration decrease and the specific conductance also decreaseThe conductance of a solution depends upon the number of ions present and hence on the concentration. To compare the conductivity of different solutions, it is necessary to take the concentration of the solutions into consideration. It is done by using equivalentconductance, l.
