answersLogoWhite

0

Sheet jointing, or eexfoliation jointing, are surface-parallel fracture systems in rock.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Earth Science

The fracturing of rock along curved lines that results when pressure is removed from bedrock?

The fracturing of rock along curved lines due to the release of pressure is known as exfoliation or sheet jointing. This process causes the outer layers of rock to peel away like an onion skin due to the reduction of overlying weight. It is common in granite and other igneous rocks.


What is the importance of jointing and bedding planes to the underground structure of caverns?

They act as conduits for the ground-waterso putting into contact with the limestone to initiatedissolution of the limestone. Consequently they also guide passage directions and morphologies. At a much later stage they control the nature of collapses in large voids.


What is sheet flow?

Sheet flow is the flow of water across a surface in a thin layer, like a sheet. It typically occurs in areas with low slope, such as flat ground or gently sloping terrain. Sheet flow is an important process in the movement of water over the land surface and can contribute to erosion and sediment transport.


A larg ice sheet that can cover land for thousands of years is a?

An ice sheet that covers land for thousands of years is known as a continental ice sheet. These are massive glaciers that form over vast areas due to the accumulation of snow and ice over long periods of time. Examples include the Antarctic Ice Sheet and the Greenland Ice Sheet.


What are sheet silicates?

A structural type of silicate mineral in which flat sheets are formed by the sharing of three of the four oxygen atoms in each tetrahedron with neighboring tetrahedrons. Also known as layer silicate; sheet mineral; sheet silicate.

Related Questions

Is Sheet jointing is due to compressional stress?

a process of swelling and shrinking continuing till the rock cracks


Is epoxy resin a jointing compound?

Epoxy resin can be used as a jointing compound.


What is tool joint finish in masonry?

Jointing


What is the best method for applying jointing sand for pavers to ensure a secure and long-lasting jointing between the pavers?

The best method for applying jointing sand for pavers is to sweep the sand into the joints between the pavers and then compact it with a plate compactor. This will ensure a secure and long-lasting joint between the pavers.


What is a jack plane use for?

A jack plane is the general-purpose bench plane, used for general smoothing of the edges, sizing of wood and [edge jointing|jointing] edges. Jack planes are about 15 inches long, and the blade can have either a slightly curved edge for smoothing stock, or a straight edge for jointing stock.


What type of jointing material must not be used on a plastic cold water storage cistern?

When working with a plastic cold water storage cistern, jointing materials that contain solvents or adhesives that can deteriorate plastic should be avoided. This includes traditional solvent cement, which can cause cracking or weakening of the plastic. Instead, use jointing materials specifically designed for plastic, such as plastic-compatible sealants or gaskets. Always check the manufacturer's guidelines for suitable jointing options.


How do you apply skim coat over damaged drywall?

If the damaged area is small then a skrim or jointing tape can be used, if the damaged area is large then it must be cut back to the joists, replaced, jointing tape applied then skimmed.


What shape should the repair boundaries form?

square or rectangular and in line with the jointing pattern


Differences between jointing and pointing?

In Civil Engineering:1 - Pointing: Pointing is act of filling the joints 15mm to 20mm from outer surface with rich mortar (1:2 ratio of Cement and Sand). This is done to obtain various objectives from detailed work which may look beautiful to make economic use of mortar where there are not enough resources to plaster and so on.Types of Pointing are, Flush, Struck, V, Grooved, Weather, Recessed Pointing and Tuck pointing.2 - Jointing: Jointing is act of layering the constructional material (Stone, Brick or Concrete Block) and also making the Joints in Concrete slabs.Differences:1- : Jointing comes first because 'Pointing' is enhancement of joints.2- : Jointing is done to bind (adher/stick/strengthen) the constructional material where'Pointing is done to make the bonds look beautiful and become resistant against weather effects and dampness.3- : Jointing is considered basic and intrisnsic to constructional work (Also called Masonry if it is done with Bricks/Stones/Blocks), where pointing is additional favor to the building.4- : Jointing deals with how building materials are to be placed with each other and how can they strengthen each other and is aided by the mortar, hence 'Jointing' needs (1) Building Material (2) Mortar; Pointing deals with how to 'ENHANCE' the JOINT by using more MORTAR, hence it needs 'MORTAR'.Hope you have understrood now.Mirza Usmanwww.facebook.com/Mirza.Usman.Blogger


What is it called when rocks in sections parallel to the surface of the rock?

Exfoliation


How can I improve my woodworking skills by mastering different techniques of wood jointing?

Mastering different techniques of wood jointing can improve your woodworking skills by enhancing the strength and aesthetics of your projects. By learning and practicing various jointing methods such as dovetail, mortise and tenon, and finger joints, you can create more intricate and durable connections between wood pieces. This will result in more professional-looking and structurally sound woodworking projects.


For what type of fitting would the application of solder wire during the jointing process be required intgral ring or capillary or type a or type b?

The application of solder wire during the jointing process is typically required for integral ring fittings or capillary fittings, as these types of fittings use soldering as the method to create a secure connection between the pipes or components. Type A or Type B fittings usually do not require soldering for jointing.