0
If you are asking about generating electricity, the first step is extracting steam from a geothermal reservoir. Once the steam is out of the ground and in pipes, the process is fairly similar for a geothermal power plant versus other types of boiler run power plants.
If this is for a smaller project at a building for a geothermal heat pump, the first step would be still providing a way to move heat to and from the earth. This would involving digging several feet into the earth, and putting in piping to allow heat transfer to occur.
Note that in both cases, energy is not being created, but simply extracted from an area of higher energy.
What else can I help you with?
Give one disadvantage to converting from fossil fuels to geothermal energy?
Converting one form of energy to other always lost some energy in the process. The use of Geothermal energy is making electricity, fossil fuel can make electricity through generator. Adding unnecessary step from fossil fuel -> geothermal -> electricity is nothing more than additional loss in energy transformation process.
How can electricity be produced from geothermal energy?
Heat from under the ground is used to make steam. This steam is used to spin turbines to generate electricity.A:In every energy-making process that involves burning a fuel (like coal or wood) the result is that the heat of that burn is used to create steam which is sent through a turbine, which spins a generator that is connected to said turbine. What geothermal energy does is replace the coal or wood, with the hot spot/hot spring, so it is used to make steam and make power.A:Geothermal is one of the sources of electricity and one of the safest, how does geothermal work, let me tell you how it works. First they need to find a hot spot, this is where there is hot fluid under the ground, the hot fluid is rain water collected over the years then the magma heats it up, but sometimes the hot spots are dead for years maybe even decades this is a con about geothermal. First they drill wells into the ground and get hot fluid which is about a 5-10 thousand feet under the ground. Then magma will flow up the pipe due to pressure under the ground, and then the pressure is lessened then turns some of the magma into steam then the steam goes to a different pipe. Then the remaining hot fluid goes to a wellhead separator, and then the hot fluid instantly vaporizes. Then the hot fluid that is not flashed into steam in the wellhead separator then goes to a standard-pressure crystallizer and turns into standard pressure steam. The remaining hot fluid goes to a lower pressure generator, which produces low-pressure steam. Then all the low-pressure, high-pressure and standard-pressure steam is transferred to a turbine. Then the remaining hot fluid goes to a reactor clarifier system and then returned to the geothermal reservoir through injection wells. Then all the steam in the plant goes to the turbine, which turns geothermal energy into mechanical energy. The force and energy of the steam spins the turbine blades. The turbine blades turn a shaft, which is directly connected to an electrical generator. Then an electrical charge is created when magnets rotate in the generator. Then the large copper bars transfer the electricity to a step-up transformer, which is outside the plant. Then inside the transformer the voltage is increased, before the power is sent to the power lines. Then the power lines carry the electricity to homes and businesses. The Geothermal source is renewable, because some of the steam in the generator turns back into the geothermal liquid and is injected back into the earth. This condensed fluid along with the fluid that did not flash to steam is injected back into the underground reservoir. Then the magma reheats the fluid, which can be used again and again.
What two steps would you take to conserve fossil fuels?
One approach to the problem is to find new sources of energy. The second way is to make the fuels that are available now last as long as possible while other solutions are being developed.
What is the term for each step in the transfer of energy and matter within a biological community?
The term for each step in the transfer of energy and matter within a biological community is a trophic level. Trophic levels represent the different levels in a food chain or food web where organisms obtain their energy.
What is the first step to the lithification process?
The first step is compaction
Give one disadvantage to converting from fossil fuels to geothermal energy?
Converting one form of energy to other always lost some energy in the process. The use of Geothermal energy is making electricity, fossil fuel can make electricity through generator. Adding unnecessary step from fossil fuel -> geothermal -> electricity is nothing more than additional loss in energy transformation process.
What is the first step on making hay?
The very first step of making hay, is the process of harvesting it from the farm.
What is the first step in making a responsible decision?
The first step in making a responsible decision is assessing and evaluating the problem.
What is the first step in making a desicion?
The first step in making a decision would be to recognize that you are in a situation in which you need to make a decision.
What is the first step in making a law?
the first step of creating a law is called First Reading!
Steps in making balut?
what is the first step in making balut
The first step in making a protein?
ribosomes.
What is good first step when making a decision?
think about the decision that you are making
The first step in making a law is to introduce a what?
The first step is to receive a number, HR for the house or S for the Senate
The first step in decision making is?
solving the problem
What is the first step of making a experiment?
Generate a hypothesis.
What is the first step in making something?
The first step in making something is usually to define the goal or desired outcome of the project. This sets the direction and purpose for the creation process.
