0
What else can I help you with?
What is the use of iodine flask?
An Iodine Flask is essential an Erlenmeyer Flask with a stopper used for the wet chemical analysis "Iodine Determination" . This analysis is typically performed on fatty acids, oils and shellac varnishes.
How do you obtain powdered iodine from liquid iodine?
Powdered iodine can be obtained by sublimation, which involves heating the liquid iodine until it changes directly into a gas and then cooling it rapidly to form a fine powder. This process allows the iodine molecules to skip the liquid phase and solidify into a powder.
What is Iodine value for Activated Carbon?
Iodine Value of Activated Carbon Apparatus: Volumetric flask, conical flask, beaker, burette, pipette, filter paper Reagents: * 0.1N Iodine solution ( 40 gm KI in 1 Ltr of Distilled water ). * 0.05N Sodium Thiosulphate solution (12.5 gm Na2S2O3.5H2O in 1 Ltr Distilled water) * 1% Starch solution * Activated carbon Procedure: I Standardisation of Iodine solution * Take 10c.c of 0.1N Iodine solution in conical flask. * Add 2 drops of Starch solution. * The pale yellow colour of Iodine Soln turns Blue. * Titrate with 0.05 N Sodium Thiosulphate till it becomes Colourless. * Burette reading corresponds to blank reading.(B) II * Weigh very accurately 0.2 gm of Activated carbon * Introduce it into the Iodine flask which should be completely dry * Add 40cc of 0.1N Iodine solution * Shake the flask for 4 minutes and filter it * Collect the filterate in a dry flask and Titrate 10cc of the filtrate against Standard Sodium thiosulphate solution using starch as indicator * Burette reading corresponds to (A) Calculations: Iodine value: C x Conversion factor; mg/gm Factor:Mol wt. of iodine (127) x normality of iodine x 40 / Wt. of carbon x Blank reading C=B-A This is dry basis test From Ishan Udyog Bhilai
Preparation of 0.1n iodine solution?
According to Kodak: For a 0.1 Normal (0.1N) solution of iodine (I2), in 1 L volume flask, dissolve 40 g potassium iodide in 25 mL water. Next, add 12.7 g iodine (I2) and dilute to 1 L. Note that a 0.1N solution is not the same as a 0.1M solution. For iodine 0.1N is 0.05M.
What happens when you mix red phosphorus Iodine crystals and ephedrine?
You get meth in about 40 minutes. Throw it all on one flask and let it sit for a while shake the flask it if starts to bubble up too much. Then when it calms down heat it to about 180f until it doesnt look like anything else is happening.
What is the use of iodine flask?
An Iodine Flask is essential an Erlenmeyer Flask with a stopper used for the wet chemical analysis "Iodine Determination" . This analysis is typically performed on fatty acids, oils and shellac varnishes.
Why is A crystal of iodine on heating in a closed flask turn into vapour and fills the complete flask?
Iodine sublimes directly from a solid to a gas when heated, without passing through a liquid phase. In a closed flask, the vaporized iodine molecules are unable to escape, so they accumulate and fill the entire volume of the flask. This process is known as sublimation.
What is the reason for the use of iodine flask for the iodine assay?
The iodine flask is used for the iodine assay because it allows for the controlled reaction between iodine and thiosulfate. The shape of the flask ensures uniform mixing and minimizes loss of iodine vapor. This setup helps in accurately determining the concentration of iodine in a solution.
What is an filtering flask?
This flask is used to collect the filtrate from the filter.
What is the use of the filterring flask?
The filtering flask is used to collect the solution resulted from a filtration.
Separation of iodine and alcohol?
The separation of iodine and alcohol can be achieved through a process known as distillation. In this process, the mixture is heated to separate the components based on their boiling points. Iodine has a higher boiling point than alcohol, so it will remain in the distillation flask while alcohol will vaporize and can be collected in a separate container.
How do you obtain powdered iodine from liquid iodine?
Powdered iodine can be obtained by sublimation, which involves heating the liquid iodine until it changes directly into a gas and then cooling it rapidly to form a fine powder. This process allows the iodine molecules to skip the liquid phase and solidify into a powder.
What is Iodine value for Activated Carbon?
Iodine Value of Activated Carbon Apparatus: Volumetric flask, conical flask, beaker, burette, pipette, filter paper Reagents: * 0.1N Iodine solution ( 40 gm KI in 1 Ltr of Distilled water ). * 0.05N Sodium Thiosulphate solution (12.5 gm Na2S2O3.5H2O in 1 Ltr Distilled water) * 1% Starch solution * Activated carbon Procedure: I Standardisation of Iodine solution * Take 10c.c of 0.1N Iodine solution in conical flask. * Add 2 drops of Starch solution. * The pale yellow colour of Iodine Soln turns Blue. * Titrate with 0.05 N Sodium Thiosulphate till it becomes Colourless. * Burette reading corresponds to blank reading.(B) II * Weigh very accurately 0.2 gm of Activated carbon * Introduce it into the Iodine flask which should be completely dry * Add 40cc of 0.1N Iodine solution * Shake the flask for 4 minutes and filter it * Collect the filterate in a dry flask and Titrate 10cc of the filtrate against Standard Sodium thiosulphate solution using starch as indicator * Burette reading corresponds to (A) Calculations: Iodine value: C x Conversion factor; mg/gm Factor:Mol wt. of iodine (127) x normality of iodine x 40 / Wt. of carbon x Blank reading C=B-A This is dry basis test From Ishan Udyog Bhilai
Why were the contents of the flask filtered?
The contents of the flask were filtered to separate the solid particles from the liquid solution. This process helps remove impurities, isolate the desired substance, or clarify the solution for further analysis or use.
How do you get pure dry iodine from a mixture of iodine and sand.?
Well every school kid knows about the 'cold finger' separation technique. Iodine changes from a solid straight to a gas when heated. It sublimes. So heat the sand/iodine mixture in a pyrex tube or flask which has a 'cold finger' inserted. The hot iodine gas will rise, hit the cold finger and form pure solid iodine crystals on the cold finger. Collect from the finger. This really is bog standard school kid chemistry.
What does collect on mean in chemistry?
collect: gather such as water droplets colllected on the flask as the water evaporated. This represents a physical change rather than a chemical change.
What causes contraction porosity in dentistry?
Insufficient pressure on the flask during processing causes porosity in denture.
