answersLogoWhite

0

Subjects>Science>Earth Science

What rivet is used for riveting magnesium alloy structures?

User Avatar

Anonymous

 ∙ 12y ago
Updated: 6/19/2024

5056 aluminum

User Avatar

Wiki User

 ∙ 12y ago

What else can I help you with?

Continue Learning about Earth Science

What is the effect of loose connection in electrical wiring system?

I would like to add two cents to the below answer on loose connections and that is where they can be overlooked. I recently bought some security flood lights from an Ebay seller. I installed one on the corner of my house and when i screwed the bulb in I noticed that it seemed to be loose in the bezel holder. I then examined the inside and found that the bezel is riveted to the insulator with a yellow brass rivet which is very thin. This rivet was loose in the bezel allowing the neutral wire to rock back and forth in the rivet. Now, no need to explain further what this loose connection can do so my advise is to check out fully the rivets that hold the bezel inside the ceramic insulators for loose connections, especially after you insert and tighten the bulb because they are not strong enough to resist the bulb be tight enough to make sure the centre of the bulb or the hot line is tight so that no looseness is there. If you tighten it up to hold most likely the rivets will loosen up after changing out the bulbs over time. If you buy a good floodlight or security light make sure the bezel in the insulator is held together with tight screws instead of rivets. Your home will be worth it.A loose neutral wire can cause abnormal arcing around its point of connection, usually resulting in the neutral wire becoming unusually hot, burning its insulation off and even causing damage to its surroundings.A loose neutral wire is also the cause of the majority of electrical fires.Arcing occurs because the loose wire does not make consistent contact. Sometimes it does make contact and sometimes it doesn't. This can happen due to a variety of factors, such as an outside supply wire swaying in the breeze (if the wire or its connections are damaged), or it can happen inside due to changes in temperature, electrical load, or mechanical disturbance.Every time the connection is made or broken, an arc forms. Usually this arc is very brief, but it is very hot and so it causes some damage every time. Thus the condition of the connection gets worse over time. At some time that can't be predicted, a large long-lasting arc may occur. This can cause damage to the surroundings, and it can start a fire.A resistive neutral is closely related to a loose neutral. A resistive neutral occurs when the neutral is connected, but it's not a very good connection. Good connections have extremely low electrical resistance, but a resistive neutral condition has an intermediate resistance -- its resistance is low enough to conduct some electricity, but too high to conduct as well as it's supposed to. This poor connection has several damaging and dangerous effects.One effect is that a loose or resistive neutral can cause abnormally high and low voltages to occur in the house wiring. For example, a cardinal sign of a resistive neutral is that lights will get brighter than normal at odd times, such as when another circuit is turned on, or when an appliance cycles on. A resistive neutral won't always cause the lights to get abnormally bright, but when it happens, it's a pretty reliable indication that you have a resistive neutral. If you are aware of a situation in which the lights get abnormally bright when other circuits are used, you should call the power company and report that you believe that there is a problem with the neutral connection. They know this can be very dangerous, so they will likely treat it as a high-priority situation.Another effect of a resistive neutral connection is that the connection becomes hot. As a result, it can overheat its surroundings and even start a fire. Even if it doesn't do either of these right away, it will tend to get worse over time because heat accelerates the ageing of the wire, its insulation, and surrounding materials.Another very dangerous effect of a loose or resistive neutral is that it can can lead to electrical shocks and even electrocution. The ways this can happen are extremely unpredictable and depend on exactly how your house is wired and the exact condition of the wiring. Here is a real example: if one resident of a certain house was in the shower when another resident used the garbage disposal, the first resident would feel a mild electrical tingle. No one else in the house could feel it. This turned out to be due to neutral wire at the electrical pole that was nearly broken. Only three strands of wire were still connected. Had the remaining strands been allowed to deteriorate further, someone would have been electrocuted. This is just one example of why it's important to get immediate attention for problems with neutral connections.

Related Questions

What rivet is used for riveting magnesium alloy?

5056 aluminum

What is a cold rivet?

riveting with out heating.

What is riveting gun?

a rivet gun is a gun

Can you give a sentence using the word rivet?

The two pieces of aluminum are held together with a single rivet. Rivet here is a noun, as it is the name of a type of fastener. Rivet the two pieces of aluminum together. In this instance it is a verb, to rivet, the action of riveting.

How do you use the word rivet in a sentence?

You can start by riveting these two pieces of steel together

What is pop riveting?

Pop riveting is a technique used to join together two pieces of metal or plastic with rivets. A hole is drilled through both pieces of metal, and the rivet is passed through both holes. Rivet pliers are placed onto the pin, and the handles are pulled together, pulling the pin head into the rivet. The pin breaks off, leaving the rivet attached firmly in place.

What is DD rivet stand for in aerospace?

2024-alloy of aluminum as a solid rivet, various shape head and length; DD is the industry-standard designation of this rivet metal alloy. The rivet head will have a mark to help indicate the basemetal alloy, which has a unique property when used/installed to fasten a joint such as two pieces of sheetmetal.

Are there any risks when pop-riveting?

Many - most are associated with fragmentation of the rivet material. Burrs break off and cause eye damage, rivet guns incorrectly set cause hand / wrist injury, rivet holes enlarged which allow the pneumatic plunger to fire a rivet through

How do you produce a good hot rivet joint?

To produce a good hot rivet joint, first make sure the rivet and the parts to be joined are clean. Heat the rivet until it glows, then quickly insert it into the pre-drilled holes in the parts to be joined. Use a pneumatic riveting hammer to upset the tail of the rivet, creating a secure joint.

How do you use a rivet snap?

To use a rivet snap, first, ensure you have a rivet and a compatible snap tool. Place the rivet into the snap's receiving hole, then position the tool over the rivet on the material you want to join. With firm pressure, squeeze the tool's handles to compress the rivet, securing it in place. Finally, release the tool to complete the riveting process, ensuring a tight and secure bond.

Why are rivets heated to red hot temperature during riveting?

There are two reasons rivets are heated to red hot temperature during riveting: to soften the metal so that the head on the opposite side can be formed by hammering the metal, and to make the rivet longer while the head is being formed so that as it cools the rivet will shorten and pull the riveted metal plates tightly together.

What is blind riveting?

Blind riveting is a fastening technique used to join materials together without requiring access to the back side of the workpiece. It involves inserting a blind rivet, which consists of a hollow body and a mandrel, into a pre-drilled hole. When the mandrel is pulled, it deforms the rivet, creating a secure connection. This method is commonly used in applications where access is limited, such as in automotive and aerospace industries.

Trending Questions
What is the greatest environmental cost of fossil fuels? Finding the number of neutrons in an element? What is solid fossil fuel formed from decaying plant remains? Where do sedimentary rocks form and what processes are involved in their formation? How cold is -200 Celsius? What is western disturbance? What volume of water mL would be added to 100 mL of 1.000 M sodium chloride solution to give a solution with concentration 0.31 M? Why is silver nitrate used in cauterization of wounds? Where can you get an h2o tail? What three interconnected factors does life on earth depend on? Why do larger sugar grains take longer to dissolve? Do cars and houses produce the same amount of pollution? Is helium metal or non metal? What are examples of standard ground observations for simple weather forecast? How many valence electrons are transferred from the calciun atom to iodine in the formation of the compound calcium iodine? What does oxygen do? What happens when bromine water is added to ethanol? In H2O how did Rikki get the locket? Thermal energy transferred by circulation of liquid or gas is called? What is the highest wind speed in Europe?

Resources

Leaderboard All Tags Unanswered

Top Categories

Algebra Chemistry Biology World History English Language Arts Psychology Computer Science Economics

Product

Community Guidelines Honor Code Flashcard Maker Study Guides Math Solver FAQ

Company

About Us Contact Us Terms of Service Privacy Policy Disclaimer Cookie Policy IP Issues
Answers Logo
Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.