How do you remove water pump on 1.8 gti?

1994 bad water pump Manual says remove pulley from power steering pump to get at bracket Pully remover rented won't budge it loose It wiggles in and out about 18 Is that normal Suggestions?

Did you remove the nut from the pulley first?

How do you replace the water pump on a 1995 Geo Metro?

The water pump for the 1995 Geo Metro is a little above and in front of the alternator. It is also bracketed behind the timing belt. So if you do not know how to or do not have the tools to work with anything involving the timing belt, I would recommend that you take your vehicle to a professional.Removal of water pump:1. Disconnect the negative battery cable2. Drain the cooling system.a. WARNING: Drain into a closable container so as not to poison your surroundings and pets.3. Remove the air cleaner assembly.4. Loosen but do not remove the 4 water pump pulley bolts.5. Raise and support the vehicle.6. Remove the lower splash shield.7. Remove the AC compressor drive belt.8. Remove the lower alternator cover plate bolts.9. Loosen the alternator adjusting bolt10. Remove the drive belt.11. Remove the crankshaft pulley.12. Remove the water pump pulley.13. Remove the timing belt.14. Remove the oil level dipstick and guide tube.15. Remove the alternator adjusting bracket from the water pump.16. Remove the water pump rubber seals.17. Remove the water pump mounting bolts and nuts.18. Remove the water pump from the vehicle.Installation: Pretty much use removal instructions but go backwards. I'll list bolt tightening in order that they should appear.1. Clean the gasket mating surfaces2. Check the water pump by hand for smooth operation.a. If the pump does not operate smoothly; replace it.b. Install the pump using a new gasket and tighten bolts to 115 inch lbs3. Install new rubber seals.4. Install the upper alternator adjusting bracket and tighten bolt to 17 ft lbs.5. When you get to the alternator cover plate and the bolts tighten to 89 inch lbs.6. When you get to the water pump pulley mounting bolts tighten to 18 ft lbs7. When you get to alternator adjustment bolt tighten to 17 ft lbs

How do you change the water pump on a 2000 Saturn SL1?

* TOOLS REQUIRED * J-43651 Water Pump Sprocket Holding Tool REMOVAL# Disconnect negative battery cable. # Remove air inlet tube and air cleaner assembly. Refer to "Air Cleaner Assembly Removal". # Drain coolant.# Remove exhaust manifold heat shield. IMPORTANT: Twist water feed pipe while pulling to remove it from water pump.# Remove thermostat and water feed assembly bolts.# Remove water pump sprocket access plate from front cover.# Install J-43651 water pump sprocket holding tool. IMPORTANT: Be sure to remove retaining bolt that is accessed from front of engine block.# Remove water pump retaining bolts. # Remove water pump assembly. INSTALLATIONNOTICE: Prior to installing the water pump read the entire procedure. Pay special attention to avoid part damage and to ensure proper sealing.# Install water pump assembly. # Install water pump bolts. Initially finger tighten bolts * Torque: 25 Nm (18 ft. lbs.)# Install the water feed tube. # Lubricate the feed tube O-ring with silicone gel lubricant. # Install water feed tube by twisting and pushing toward water pump. Take care not to tear or damage the O-ring. # Install thermostat housing to block bolts. * Torque: 10 Nm (89 inch lbs.)# Install exhaust manifold heat shield.# Install air cleaner assembly and air inlet tube. Refer to "Air Cleaner Assembly Installation". # Connect negative battery cable. # Add coolant.

What is the cargo capacity of the 2004 Volkswagen GTI with all seats in place?

The 2004 Volkswagen GTI has 18 cu.ft. of cargo capacity with all of its seats in place.

What is the cargo capacity of the 2006 Volkswagen GTI with all seats in place?

The 2006 Volkswagen GTI has 18 cu.ft. of cargo capacity with all of its seats in place.

What is the cargo capacity of the 2002 Volkswagen GTI with all seats in place?

The 2002 Volkswagen GTI has 18 cu.ft. of cargo capacity with all of its seats in place.

What is the cargo capacity of the 2005 Volkswagen GTI with all seats in place?

The 2005 Volkswagen GTI has 18 cu.ft. of cargo capacity with all of its seats in place.

What is the cargo capacity of the 2003 Volkswagen GTI with all seats in place?

The 2003 Volkswagen GTI has 18 cu.ft. of cargo capacity with all of its seats in place.

What is the procedure for changing a water pump on a power stroke diesel in a 2003 F250?

REMOVAL: 1. Partially drain the engine cooling system. 2. Remove the upper radiator hose clamps and upper radiator hose. 3. Disconnect the radiator coolant recovery reservoir hose at radiator. 4. Remove the fan and clutch assembly using fan clutch nut wrench and fan clutch pulley holder (you can rent one from local parts store). Set fan and clutch assembly in fan shroud. NOTE: Fan clutch has right-hand thread. Remove by turning nut counterclockwise. 5. Remove the fan shroud screws. 6. Remove the fan shroud, and fan and clutch assembly. 7. Loosen the water pump pulley bolts. 8. Remove the drive belt. 9. Remove the water pump pulley bolts and water pump pulley. 10. Disconnect the engine coolant temperature sensor (ECT sensor). 11. Disconnect the heater hose and clamp from water pump. 12. Remove the water pump inlet bolts and water pump inlet. 13. Remove water pump bolts. 14. Remove water pump and water pump housing gasket. 15. Clean gasket surfaces. INSTALLATION: 1. Install the water pump and water pump housing gasket. 2. Install the water pump bolts, tighten bolts to 15 ft-lb. 3. Install the water pump inlet and bolts, tighten bolts to 15 ft-lb. 4. Install the heater hose and clamp to the water pump. 5. Connect the engine coolant temperature sensor. 6. Install the water pump pulley and start the water pump pulley bolts. 7. Install the drive belt. 8. Tighten the water pump pulley bolts to 12-18 ft-lb. 9. Install the fan shroud, and fan and clutch assembly. 10. Install the fan shoroud screws. 11. Install the fan and clutch assembly using fan clutch nut wrench and fan clutch pulley holder. NOTE: Remember it is right-hand threaded. Install by turning nut clockwise. 12. Install the radiator coolant recovery reservoir hose to radiator. 13. Install the upper radiator hose and clamps. 14. Refill and bleed the engine cooling system. Takes around 2 hours to complete, maybe less. Enjoy! -Mike

Where is the thermostat in a 2004 Pontiac grandprix?

2004 Pontiac thermostat Service and Repair 2004 Pontiac Thermostat Replacement 2004 Pontiac Removal Procedure : 1. If equipped with an automatic transmission, remove the exhaust manifold. 2. Drain the cooling system. 3. Remove the thermostat housing to water pump feed pipe bolts. 4. Remove the thermostat housing to water pump feed pipe. 5. Remove the thermostat. Installation Procedure 1. Install the thermostat. 2. Install the thermostat housing to water pump feed pipe. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the thermostat housing to water pump feed pipe bolt. ^ Tighten the thermostat housing to water pump feed pipe bolt to 10 Nm (18 inch lbs.). 4. If equipped with an automatic transmission, install the exhaust manifold. 5. Fill the cooling system.

What are torque specs for WATER PUMP Mercedes 420 SEL?

Torque specs for WATER PUMP Mercedes 420 SEL are: 7.3 diesel and 15 to 18 foot pounds of torque

What is the torque specification on a water pump for a 1998 buick skylark wth a 3.1 liter engine?

According to the chilton manual the 5 water pump bolts torque to 89 inch pounds. The four bolts that hold the water pump pulley torque to 18 foot pounds.