0
CALORE LOW PROFILE CERAMIC ELECTRIC SPACE HEATER MANUAL INFO OPERATION TURN ON CONTROL
ATTENTION READER: THE FOLLOWING WAS COPIED DIRECTLY FROM THE COMPANY INSTRUCTION BOOKLET AND OMITS SOME INFORMATION AND MAY CONTAIN ERRORS. IT DOES NOT INCLUDE ALL INFORMATION CONTAINED THEREIN AND THE AUTHOR HERE (ME) DOES NOT ASSUME ANY LIABILITY, RISK OR RESPONSIBILITY FOR ANYONE OPERATING THEIR UNIT BASED UPON THIS INFORMATION. I REPEAT, UTILIZE THIS INFORMATION AT YOUR OWN RISK. BY ACTING UPON THIS INFORMATION YOU ASSUME ALL LIABILITY! I HAVE TRIED TO INCLUDE ALL SAFETY WARNINGS!
CAUTION: High temperature. Keep electrical cords, drapery, and other furnishings at least 3 feet (.9m) from the front of the heater and away from every side and rear.
WARNING: To reduce the risk of fire, electric shock, or personal injury, read all of the instructions before using the heater. This appliance is intended for household or personal use only as described. Any other use including but not limited to commercial, agricultural, or outdoor use is not recommended by the manufacturer and may cause fire, electric shock, injury and/or damages. The use of attachments, accessories, OR EXTENSION CORDS NOT RECOMMENDED or sold by Tropical Breeze Products may cause hazards and void the warranty.
Heater has HOT electrical spark or arc and should not be used around flammable gas/liquid/objectszperiodz
Heater has overturn protection system that shuts off the heater when parts of the heater are getting excessively hot. If the heater shuts off, immediately turn the heater OFF and inspect for any foreign objects on or adjacent to the heater that may cause high temperatures. DO NOT OPERATE THE HEATER UNTIL IT IS RESET. To reset the heater, turn it OFF, unplug it from the electrical outlet and wait five to ten minutes for the unit to cool down before plugging it back in and turning the heater on.
ALWAYS UNPLUG THE HEATER WHEN NOT IN USE!
Avoid the use of an extension cord because it may overheat and risk fire. However, if you have to use an extension cord, the cord should be a No. 14 AWG minimum size and rated not less than 1875 Watts.
Calore Low Profile Heater Model 63005 an/or PH-816EF operation information control manual says:
1.Plug the power supply cord into a wall outlet (110/120VAC, 60Hz)
IMPORTANT: THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) TO REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG IS INTENDED TO FIT INTO A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY INTO THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE!
BUTTONS:
Power/Mode - Two buttons provide same function - The Circle with Vertical Line at Top of circle. One is foot switch at left end floor level and the other is on the operation LED panel bottom right. BOTH OPERATE SAME FUNCTION.
"+" & "-" button is up/down switch on panel left, used for setting desired temperature and setting time length of operation desired.
The Circle with 9AM clock hands is used for changing mode to set time length.
The LED Display with numbers shows Room Temp by default, will show desired temp when setting thermostat (will flash and then stop when set), and will show hours (length of time heater will be on) with a default of 3 hours, but when setting will flash and then stop when time is set).
2. TURNING THE HEATER ON: To turn the heater ON, press the MODE button. The heat setting will be set to AUTO. Press the MODE button again to set to HEAT.
3. TURNING THE HEATER OFF: To turn the heater OFF, press the MODE button in the HEAT setting. The heater will turn off and the LED will remain on and will display the current room temperature.
4. SETTING THE THERMOSTAT: Press the MODE button, set to AUTO mode to engage the automatic thermostat
5. SETTING THE TEMPERATURE: To set the desired temperature Press the "+" to increase the temperature or the "-" button to decrease the temperature.
The desired temperature will set and execute after the LED display stops flashing and displays the room temperature again. This is your ideal setting. The heater will start automatically when the room temperature drops below the set point and will turn off when the set point is reached.
The default temperature setting is preset from the factory at 70 degrees Fahrenheit and will turn off when the set temperature is reached.
The range of temperature setting is from 50-85 degrees Fahrenheit.
6. SETTING THE TIMER:
1. Press the TIMER button until the Set Time starts flashing. The default value is 3 hours.
2. Press the "+" button to increase the set time or the "-" button to decrease the set time.
The Timer can be set from 1 hour to 12 hours. The Timer will set and execute after the LCD display stops flashing. The heater will shut OFF automatically when the set time is reached.
3. To run the Timer OFF, follow step 1 and press the "-" button to set the timer to 0. The Timer feature will turn off when the LCD stops flashing.
Maintenance
1. Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning your heater.
2. Light accumulated dust may be removed from the heater with a soft cloth or vacuum cleaner.
3. Wipe the exterior surfaces of the heater occasionally with a damp cloth (NOT DRIPPING WET) using a solution of mild detergent and water. Dry the case thoroughly before operating the heater.
CAUTION: Do not allow water to run into the interior of the heater as this could create a fire or electric shock hazard.
4. Store the heater in dry lace when not in use.
WARNING: Any other servicing needed must be performed by an authorized service representative. DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.
Product Specs:
Model#: PH-816EF (these instructions came in sealed box for Model #63005)
Voltage: 120V, 60Hz
Current: Maximum continuous draw, 12.5 amps
Output: 5200 BTUs
Power: 1500 watts
Enclosure: Metal Body: Plastic End Cover
What else can I help you with?
How do I reset the electric water heater reset button?
To reset the electric water heater reset button, locate the button on the heater's control panel and press it firmly. This will reset the heater and restore its functionality.
How can you refurbish an electric heater control valve?
Buy a new one!
What costs more in electricity - electric heater or electric guitars?
electric heater
Where is the heater control valve on a 2001 Chrysler Town and Country located?
A 2001 Chrysler Town and Country does not have a water control valve in the heater system. The cabin temperature is controlled with electric motors on airflow control doors.
Is the hot water heater gas and electric?
Gas heater & electric heater both are available.
What are the features of an efficient electric heater?
The main feature of an efficient electric heater is, that is used up to 30% less engery than a conventional electric heater. This reduces the cost of the heater.
Where is the heater control cable located on a 1998 Dodge Caravan?
No cable, all controls are done with electric motors.
Where is the heater control valve located on a 1997 Chrysler LHS?
It does not have a heater control valve.It does not have a heater control valve.
What is electric water heater which used in house?
An electric water heater in a hot tank is called an immersion heater and many of those run at 3 kW with a thermostat to control the max temperature. Power showers use a type of water heater that heats the water at the point where it is used, without a tank. They run at 6-8 kW and are also controlled by a thermostat.
How do I turn on a Rheem water heater?
To turn on a Rheem water heater, locate the gas control valve or the power switch on the unit. For a gas water heater, turn the gas control valve to the "on" position. For an electric water heater, flip the power switch to the "on" position. Wait for the water heater to heat up before using hot water.
What is the adjective the electric heater in the living room had exploded?
The adjective is electric, because it is describing the heater.
What are the benefits of using an electric in-line water heater in a residential setting?
An electric in-line water heater in a residential setting offers benefits such as energy efficiency, continuous hot water supply, space-saving design, and precise temperature control.
