0
A digital signal is actually a complex signal. Consider the horizontal part of a digital signal as a component with 0 frequency and the vertical part of the signal as the component of infinite frequency. Also, consider the change from the horizontal to vertical as all the frequencies. Then we can claim that a digital signal is complex signal with frequencies from 0 to infinite.A digital signal is a composite analog signal with an infinite bandwidth.
What else can I help you with?
What is the effect of bandwidth on a digital signals?
Bandwidth is an inherent characteristic of a given transmission channel, or is determined by the narrowest-bandwidth component of the system. The bandwidth of a channel will limit the possible attainable data rates. This is shown simply by Shannon's Theorem, which states C = B log_2 (1+P_signal/P_noise), where C is the channel capacity in bps, B is the channel bandwidth in Hz, P_signal is the power of the detected signal in W, and P_noise is the noise power of the detected signal in W. As an example, consider a standard phone line (i.e., using a dial-up modem). Standard phone lines have a bandwidth of about 3.4 kHz and a signal-to-noise ratio of about 10,000. Using this information, we get C = (3.4 kHz) log_2 (1+10,000) = 45 kbps. Dial-up modems can actually get as high as 56 kbps, but that is beyond the scope of this question. In general Shannon's Theorem can provide a fairly accurate way to predict the possible data rates for a given transmission channel if the bandwidth and resulting signal and noise powers are known.
Is low bandwidth signal has more power than high bandwidth signal?
no,because generally the lower frequency side existed for lower bandwidth,and higher frequency side existed higher bandwidth,so thus we can say that lower bandwidth has generally has lower power as compared to higher bandwidth.
What are basic elements of digital signal processing?
The basic elements in digital signal processing are an analog to digital converter, digital signal processor, and digital to analog converter. This process can take an analog input signal, convert it to digital for processing and offer an analog output.
Explain the characteristics of a digital signal?
what are the characters of digital signal
Webex bandwidth requirements?
Transmission bandwidth depends on modulating signal frequency and carrier frequency
What is an analog-to-digital converter?
An analog-to-digital converter is a device which converts an infinite resolution analog signal to a finite resolution digital signal.
What is shanon capacity?
digital bandwidth = analogue bandwidth * log2 (1+ SNR) where SNR = strenthe of signal power/ strength of noise larger the SNR it is better.
What is convert analog to digital convert?
An analog-to-digital converter is a device which converts an infinite resolution analog signal to a finite resolution digital signal.
Does a low bandwidth signal have more power than a high bandwidth signal?
A low bandwidth signal does not have more power.
What is relationship between signal spectrum and bandwidth?
Signal Bandwidth is the Bandwidth of particular frequency at which signal is transmitted and Bandwidth of spectrum which can able two show number of signal between Intrest of frequency.
As speed increases which parts of a digital signal increases?
As speed increases, the frequency content of the digital signal increases. This means that the rate at which individual cycles of the signal occur within a given time interval will increase. Additionally, the bandwidth required to transmit the digital signal also increases to accommodate the higher frequencies present.
Why the frequency of a digital signal is infinite?
actually the frequency of a digital signal in infinite because assuming the signal is a square wave for each point in time eg 1 sec the amplitude can remain at max or "dc" for any number of bits assuming 1 bit = dc for 1 sec/clock cycle
What is the bandwidth of facsimile signal?
facsimile signal requires a bandwidth of only about 1000 Hz
Why it is generly true that a digital signal required high bandwidth than analog signal?
A: Analogue signal Direct voltage that varies in the low spectrum of frequency on digital signal the information is deciphered in micro seconds therefore the frequency must be hi the higher the better.
What signal has wider bandwidth sine wave with frequency 100HZor 200HZ?
The signal with a frequency of 200Hz has a wider bandwidth compared to a signal with a frequency of 100Hz. Bandwidth is determined by the range of frequencies present in a signal, so a higher-frequency signal will have more frequency components and thus a wider bandwidth.
What is essential bandwidth of FM signal?
"Essential bandwidth" is the portion of the signal spectrum that encompasses most of the energy of the original signal in the frequency domain.
What is bandwidth required for AM signal?
With full double sideband AM the bandwidth of the modulated signal is twice that of the baseband information signal. With suppressed carrier single sideband AM the bandwidth of the modulated signal is identical to that of the baseband information signal. With vestigial sideband AM the bandwidth of the modulated signal is somewhere between the above two cases, depending on how much of the vestigial sideband is included.
