answersLogoWhite

0

Yes. Setup the 555 as an oscillator and plug the capacitor under test into it and measure the frequency of the signal generated. For more precision, measure the charge time only, and use a constant current source, but that is getting more complicated than need be - there are far better ways to test a capacitor than with a 555.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering
Related Questions

Is it possible to measure capacitance using only one 555 timer?

yes, it is possible to measure capacitance using only one 555 timer for it's monostable operation. When the output is high time is given by the equation t=1.1RC. From the output pulse measuring t(high) and then by measuring R we can calculate the capacitance.


How do you make a 30 second timer?

You can use the 555 timer to make a one minute solid state timer.


Why 555 timer named as 555?

A 555 timer basically consists of: # A voltage divider circuit, # Two comparators, # An SR flip-flop, and # Two (bipolar) transistors: one NPN (discharge) and one PNP (reset), as can be seen in its block diagram. The voltage divider consists of three 5Kohm resistors, so that we get (1/3)Vcc and (2/3)Vcc; we use these voltages as references for the comparators. The three 5K resistors, along with IC's main applications being in timer and multi-vibrator circuits, give it the name 555 timer.


What does a 555timer do?

The 555 timer IC is an integrated circuit (chip) used in a variety of timer, pulse generation, and oscillator applications. The 555 can be used to provide time delays, as an oscillator , and as a flip-flop element . Derivatives provide up to four timing circuits in one package.


What is the roles of 555 timer circuit?

The 555 timer IC is a device that can create various kinds of time delays in a circuit. It uses a threshold pin that is typically connected to an RC circuit. Depending on how it is connected, it can operate in one shot mode (monostable), astable mode (retriggerable), or schmitt trigger mode.


What size res and cap are needed in a 555 IC timer circuit to get 1 minute once every hour cycle?

A: the lm555 timer is laser trim with a ratio of .639 then decide whether one minute hi or low


How do you measure the capacitance of 3 phase capacitor in active line voltage of 3 phase circuit?

You measure the capacitance of a capacitor in an active circuit by observing the voltage across it and the current through it. That gives you, by Ohm's law, the impedance of the capacitor. Plug that in the the equation for capacitive reactance, and you get capacitance. Note: There is no such thing as a three phase capacitor. A capacitor is a two terminal device that resists a change in voltage inversely proportional to its capacitance. You connect one capacitor to one phase. If you have a "three phase capacitor", then you are talking about three capacitors. Deal with each one separately.


How 555 timer is used to generate square wave?

The 8-pin 555 timer must be one of the most useful ICs ever made and it is used in many projects. With just a few external components it can be used to build many circuits, not all of them involve timing!A popular version is the NE555 and this is suitable in most cases where a '555 timer' is specified. The 556 is a dual version of the 555 housed in a 14-pin package, the two timers (A and B) share the same power supply pins. The circuit diagrams on this page show a 555, but they could all be adapted to use one half of a 556.Low power versions of the 555 are made, such as the ICM7555, but these should only be used when specified (to increase battery life) because their maximum output current of about 20mA (with a 9V supply) is too low for many standard 555 circuits. The ICM7555 has the same pin arrangement as a standard 555.The circuit symbol for a 555 (and 556) is a box with the pins arranged to suit the circuit diagram: for example 555 pin 8 at the top for the +Vs supply, 555 pin 3 output on the right. Usually just the pin numbers are used and they are not labelled with their function.The 555 and 556 can be used with a supply voltage (Vs) in the range 4.5 to 15V (18V absolute maximum).Standard 555 and 556 ICs create a significant 'glitch' on the supply when their output changes state. This is rarely a problem in simple circuits with no other ICs, but in more complex circuits a smoothing capacitor (eg 100µF) should be connected across the +Vs and 0V supply near the 555 or 556.Source: http://www.kpsec.freeuk.com/555timer.htm


What is the operation of the monostable multiviator circuit using 555?

The 555 timer is commonly used in IC electronics and in electronic circuits. In the monostable multivibrabor mode, the 555 works as a pulse generator. In astable mulitvibrator mode, the 555 is free running, and goes back and forth between frequencies.


What is an NE555's job in a circuit?

A 555 chip is used as a timer. In a monostable circuit the chip will send one pulse after a period of time. If the chip is in a astable circuit it will send pulses forever.


What has a 555 timer IC in it so I can desolder it and use it?

The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty cycle are accurately controlled with two external resistors and one capacitor. The circuit may be triggered and reset on falling waveforms, and the output circuit can source or sink up to 200mA or drive TTL circuits. There is little point in desoldering one since they are very cheap to buy since the chip is nearly thirty years old. NE/SA/SE555/SE555C Timer circuits are all over the net.


What is a one timer?

a one timer is when u have one boyfriend at one time okii stupid