0
What else can I help you with?
Effect of putting a leaked diode in a circuit?
The effect is quite simple, to be honest. When putting a leaked diode in a circuit, it will cause the other ones to break down.
What is the Effect of collector resistance in emitter follower circuit?
Colector resistance in an emitter follower circuit serves to place a limit on how much current can be supplied by the transistor. Often, the resistor is sized so that a short circuit in the load does not cause the transistor to fail.
Why is current the same in all points of a circuit even with resistors on it?
Electrical current (amperes, or coulombs per second) is the flow of electrons from one point to another. In a series circuit, there is only one path for those electrons to flow, so the amount of flow at different points in a series circuit is always the same. That's not to say that the current does not change - certainly different resistance, for instance, would cause different current - the point here is that, for a given set of conditions, the current in a series circuit is the same at every point in the circuit. This is Kirchoff's current law. The signed sum of the currents entering a node must always be equal to zero. If a node consists only of two elements, then the current entering the node from one element must be equal to the current leaving into the other element. Since a series circuit consists only of nodes with two elements connected together, that means the current at every point in a series circuit is the same. Think of this analogy. Connect several water hoses in series with modulating valves between each section. Apply water pressure to one end. Make different adjustments to the valves, representing different resistances. Note that, although the water pressure is different at different points (think voltage), the current flow at different points (think current) is the same.
When a dead short occur what happens to circuit resistance?
The circuit resistance is likely to gradually drop and in such case it will cause the circuit to burn down.
What is loading affect of multimeter?
'Loading effect' applies to voltmeters, or to multimeters when set to measure voltage. It describes the change in a circuit's resistance when the resistance of the voltmeter is taken into account. It's effect is to cause the resulting measuredvoltage to be different from the actual voltage which would appear without the voltmeter connected. The loading effect is minimised by ensuring that the internal resistance of the voltmeter is significantly higher than the resistance of that part of the circuit to which it is connected. For general voltage measurement, this is usually the case anyway, but when measuring circuits which, themselves, have very high resistance care must be taken over the choice of voltmeter to be used.
Why do resistors get hot?
Resistors get hot because they convert electrical energy into heat while resisting the flow of electricity. This heat is a byproduct of the resistance in the circuit and can cause the resistor to become hot to the touch.
What are the difference in cause and effect?
the different between cause and effect.... cause=what cause the problem or what cause it to become a problem effect=what effect did it have on it hope that help u(:
Effect of putting a leaked diode in a circuit?
The effect is quite simple, to be honest. When putting a leaked diode in a circuit, it will cause the other ones to break down.
What is between different cause and effect?
cause is what made something happen. Effect is what was the result was.
No clock or radio disply 2001 Mercury Villager but the CD changer and radio work just fine?
These radios are notorious for the displays going blank. I have a 1999 Villager Estate that had the same problem. The cause is usaully a set of large resistors on a circuit board inside the radio. The resistors get so hot that the solder connecting them to the circuit board actually melts and they become disconnected. The repair involves opening the radio, finding and resoldering the large resistors. They can be identified by the heat discoloration that they cause on the circuit board. This isn't too difficult, but if you have no experience using a soldering iron, then you may want to take the radio to a friend with a bit of soldering experience.
What is the effect on current in a wire if both the voltage across it and its resistance are doubled?
it will cause a Short Circuit
What is effect of an unbypassed resistor on the common emitter amplifier circuit?
An emitter resistor in a common emitter circuit will cause the stage to experience the effects of degenerative feedback if it is unbypassed. The degenerative feedback reduces gain. This is probably the primary effect in the described circuit.
What will happen when switches s1 and s3 are closed?
When switches s1 and s3 are closed, the resistors in the circuit will be in parallel, resulting in a lower total resistance. This will increase the current flowing through the circuit and may cause the bulbs or other components to become brighter or draw more power.
Explain flywheel effect of a tank circuit?
Fly wheeling or ringing is a process where by circulating current will cause a ringing effect where that is useful is on SCR circuit to reverse power for a shot time enough to reduce holding current therefore shutting the device off
What clue word best tells you that a cause is producing an effect?
The word I'd have to say is "change" or "different" for the cause is changing the situation. That's why I think it's called "cause and effect" because the effect is the effect of the change. Sorry if I sounded like a brainiac there....
What is the only type of study that demonstrates cause and effect?
The only type of study that can demonstrate cause and effect is a randomized controlled trial (RCT), where participants are randomly assigned to different groups to receive different interventions. This design allows researchers to establish a cause-and-effect relationship between the intervention and outcomes.
What is the Effect of collector resistance in emitter follower circuit?
Colector resistance in an emitter follower circuit serves to place a limit on how much current can be supplied by the transistor. Often, the resistor is sized so that a short circuit in the load does not cause the transistor to fail.
