0
What else can I help you with?
What gauge wire is required to hook up an electric kitchen stove?
Normally a new kitchen stove will require a 50 amp breaker wired with AWG # 6/3 with ground wire.
What is a sentence with the word electric current in it?
The electric light bulb would not turn on because it was burnt out.
How do you wire a 220v three prong to a 220v four prong?
You'll need to contact an electrician who will pull a new wire for you. If you only have 2 wires on the 240 line, you don't have a neutral or a ground; both of which are essential for a modern electric range.
How do you rewire?
The usual procedure is to remove the old wire and replace it with new wire.
What size wire do you need to run a 240V plug for a dryer?
the size of the wire that you need to run depends on the the amperage of the device/appliance you'll be hooking up to that line. Use #12 wire for 20 amp, #10 for 30 amp, #8 wire for 40 amps and #6 for 50 amps. Hope that helps.
Where can one purchase a new electric furnace?
My electric furnace has suddenly stopped working. Where can I buy a new one?
How much does it cost to purchase and install a new gas furnace in the New York area?
Depending on the brand of furnace and the grade of furnace, and also if it is electric or not, and who installs it, it can be anywhere from 2,000 dollars to 10,000 dollars.
Where can I get a new electric furnace?
if your heater just went out in your house and you need a really good electrical furnace you should really consider getting a whole new furnace from a hardware store or a heater store.
Where can I find out about heating my home with an electric furnace?
I am looking for a new and efficient heating system in my home and it has been suggested to me that I might benefit from getting an electric furnace. Where can I find out more information about them?
What is the first step to replacing my electric furnace with a gas furnace?
Meet with your installer to determine the capacity of your new furnace. The furnace capacity should be matched with the size of the house. You want to get a furnace that heats a house without overheating the home. Because your furnace will be newer, it will take less energy to heat your home.
How can I ensure a successful installation of an electric furnace in my home?
To ensure a successful installation of an electric furnace in your home, it is important to hire a licensed and experienced HVAC professional. Make sure the installation is compliant with local building codes and regulations. Properly size the furnace for your home's heating needs and ensure that the electrical system can support the new furnace. Regular maintenance and servicing of the furnace will also help ensure its long-term performance and efficiency.
New furnace and thermostat now air conditioner compressor doesn't work?
If you replaced the furnace and thermostat this past winter, and now the A/C doesn't work. You probably just have a loose control wire. Check the yellow wire at the stat. It should be on the Y terminal. Next, look inside the furnace at the terminal block. The condenser wire should have two conductors. One hooks up with the yellow wire on the Y terminal of the terminal block. The other hooks to the C terminal. Always turn off the breaker to the furnace before working on any wiring. No need to fry the transformer.
How can I safely install a new wire for my electric dryer?
To safely install a new wire for your electric dryer, first turn off the power to the dryer at the circuit breaker. Then, remove the old wire and install the new wire following the manufacturer's instructions. Make sure to use the correct gauge wire for your dryer and secure all connections tightly. Finally, turn the power back on and test the dryer to ensure it is working properly.
How do you reline furnace firebox?
u dont you buy a new furnace
do they cove rif u need a new furnace?
do grants cover new furnace if u have the gravity style
How do I properly install an electric dryer wire?
To properly install an electric dryer wire, first turn off the power to the dryer. Then, remove the old wire and connect the new wire following the manufacturer's instructions. Make sure to secure the connections tightly and test the dryer before using it. If you are unsure, it is best to consult a professional electrician for assistance.
How can I safely install a new wire for my electric stove?
To safely install a new wire for your electric stove, follow these steps: Turn off the power to the stove at the circuit breaker. Remove the old wire carefully, making sure to disconnect it properly. Install the new wire following the manufacturer's instructions and local electrical codes. Secure the wire in place and ensure there are no exposed wires. Turn the power back on and test the stove to make sure it is working properly. If you are unsure or uncomfortable with any step, it is best to consult a professional electrician for assistance.
