answersLogoWhite

0

You should first remove your old bathroom light fixtures and then very careful screw in the new bathroom light fixtures. It is a good idea to have the electricity off so you don't hurt yourself.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you covert 277 light fixtures to 110 light fixtures?

You need to rewire to a lower voltage at panel or get a transformer that steps down 277 to 110 volts. Make sure wire is sized for new load as well as breaker.


Kitchen Lighting Design?

form_title=Kitchen Lighting Design form_header=Cook with the best lighting! Install new kitchen lighting with help from professionals. What kind of kitchen lights do you currently have?=_ What type of lighting do you want?=_ How many light fixtures do you currently have?= {(),1,2,3,4,5,6,7,8,9,10}


How do you install a GFCI so it is always on to a two way light switch that controls a vent and a light in a bathroom?

Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.


What to do if you want to install new recessed lights in the kitchen the lights that are in the ceiling now do not have a box therefore nowhere to put the ground wire which is on the new light?

See View Discussion below.


How do you install a new ventilation fan on a second light switch using the power from the existing light switch?

you probably can't, you need a neutral and a live wire to make a fan work. switches normally only have live wires.

Related Questions

How can I replace bathtub fixtures in my bathroom?

To replace bathtub fixtures in your bathroom, first turn off the water supply. Remove the old fixtures by unscrewing them and disconnecting any pipes. Install the new fixtures by following the manufacturer's instructions. Secure them in place and reconnect the pipes. Turn the water supply back on and test the new fixtures for leaks.


Bathroom Lighting Design?

form_title=Bathroom Lighting Design form_header=Install the perfect lighting for your bathroom. What type of fixtures do you currently have installed?What type of fixtures do you currently have installed?=_ Do you wish to add additional lighting?= () Yes () No () Not Sure How many bathrooms need new lighting?= {(),1,2,3,4,5}


How can I install new shower fixtures?

To install new shower fixtures, first turn off the water supply. Remove the old fixtures by unscrewing them. Clean the area and apply plumber's tape to the new fixtures. Install the new fixtures by screwing them in place. Turn the water supply back on and test for leaks.


How can I install fluorescent light fixtures in my home?

To install fluorescent light fixtures in your home, follow these steps: Turn off the power to the area where you will be installing the fixtures. Remove the existing light fixture and disconnect the wires. Install a new fluorescent light fixture according to the manufacturer's instructions. Connect the wires, making sure to match the colors. Secure the fixture in place and turn the power back on to test the light. If everything is working properly, you have successfully installed the fluorescent light fixtures in your home.


What are the steps to replace plumbing in a bathroom?

Turn off the water supply to the bathroom. Remove fixtures and fittings such as sinks, toilets, and bathtubs. Cut and remove the old pipes. Install new pipes and fittings. Connect the new fixtures and fittings. Test the new plumbing system for leaks. Reinstall any removed fixtures and fittings. Turn the water supply back on and check for proper functioning.


Where can bathroom lighting fixtures be purchased?

My bathroom needs new lighting. Which companies provide bathroom lighting fixture?


How can I replace the subfloor in a bathroom?

To replace the subfloor in a bathroom, follow these steps: Remove the existing flooring and fixtures. Cut out the damaged subfloor using a saw. Measure and cut a new subfloor to fit the space. Install the new subfloor using screws or nails. Replace the flooring and fixtures. Seal the edges to prevent water damage.


How can I properly install a double sink plumbing system in my bathroom?

To properly install a double sink plumbing system in your bathroom, you will need to follow these steps: Turn off the water supply to the bathroom. Remove the existing sink and plumbing fixtures. Install a new drain pipe for the second sink, connecting it to the existing drain line. Install the new sink and faucet fixtures, making sure they are securely attached. Connect the water supply lines to the new fixtures. Test the system by turning on the water and checking for any leaks. Make any necessary adjustments to ensure proper drainage and water flow. It is recommended to consult a professional plumber if you are unsure about any step in the installation process.


What are the best ways to upgrade bathroom fixtures?

To upgrade bathroom fixtures, consider replacing old fixtures with new ones that are modern and energy-efficient. This can include installing new faucets, showerheads, toilets, and lighting fixtures. Additionally, updating the hardware such as towel racks, toilet paper holders, and cabinet handles can give the bathroom a fresh look. Make sure to choose fixtures that match the overall style and design of the bathroom for a cohesive look.


How can I convert a tub to a shower in my bathroom?

To convert a tub to a shower in your bathroom, you will need to remove the tub, install a shower pan, add waterproofing materials, and install new shower fixtures. It is recommended to hire a professional plumber or contractor for this project to ensure it is done correctly and safely.


Carefully Choose Bathroom Light Fixtures?

Many people spend a lot of money remodeling their bathroom, but they leave their old bathroom light fixtures in place, ruining the look and feel of their new room. Many new and exciting lighting options are available for the modern home, so choosing the light fixture should be at the top of the list for any redecorating project. Modern and traditional lighting designs form important parts of any renovation. Homeowners should carefully choose fixtures that match the rest of the room dcor to create a unified design.


How can I install a bathroom sink light to enhance the lighting in my bathroom?

To install a bathroom sink light, first turn off the power to the area. Remove the old light fixture and disconnect the wires. Install the new light fixture according to the manufacturer's instructions, making sure to secure it properly. Connect the wires, ensuring they are securely fastened. Turn the power back on and test the light to ensure it is working properly.