answersLogoWhite

0

Simply multiply the peak voltage to 2 and you will get the peak to peak voltage.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Convert rms to peak to peak power?

P-P voltage = RMS voltage * 2 * sqrt (2)Here's an example: house voltage is 120VRMS, which is actually ~169 volts peak - neutral. double this will give peak to peak value.


What is peak to peak voltage?

Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.


Convert 8 amp motor to peak horsepower?

Need to know the voltage and phase for this question.


How rms voltage related to peak voltage?

The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.


What is the resistance of a bulb that uses an average power of 75 W when connected to a 60 Hz power source with a peak voltage of 170V?

You have to convert the peak voltage to an r.m.s. value, before inserting that value into the power equation.


How do you convert vrms to vpp?

Vrms = Vpp/squareroot(2)This can be written another way:Vrms * squareroot(2) = VppAnswerThe question asks for the relationship between the rms value of voltage, and the peak-to-peak value of voltage, not the peak value (Vmax) of voltage, so:Vp-p = 2 Vmax = 2(1.414) Vrms = 2.828 Vrms


What is the peak-to-peak voltage in a circuit with an rms voltage of 120VAC?

ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41


How do you you convert 3V p-p to Vdc?

To convert a 3V peak-to-peak (p-p) AC voltage to a direct current (DC) voltage, you would typically use a rectifier circuit followed by a smoothing capacitor. The peak voltage of the AC signal is 1.5V (since p-p is double the peak), so the average DC voltage after full-wave rectification would be approximately 1.5V multiplied by 0.9, yielding about 1.35V DC. However, the exact DC output will depend on the efficiency of the rectification and filtering process used.


What is a peak load voltage out of a bridge rectifier for a secondary voltage of 15 Vrms?

A: Peak voltage is RMS multiplied by a factor of 1.41


How do you measure peak voltage using oscilloscope?

To measure peak voltage using an oscilloscope, adjust the voltage scale setting on the vertical axis until the entire waveform is visible on the screen. Then, use the cursors or measurement tools on the oscilloscope to determine the maximum amplitude of the waveform, which represents the peak voltage. You can directly read the peak-to-peak value if it's available, or calculate it by multiplying the peak voltage by 2 if only the peak amplitude is displayed.


What is difference between amplitude and peak value?

It is the highest value of the amplitude, called the peak value. Scroll down to related links and look at "RMS voltage, peak voltage and peak-to-peak voltage". Look at the figure in the middle below the headline "RMS voltage, peak voltage and peak-to-peak voltage".


How do you calculate the voltage average 240v from a 325v 50Hz sine wave peak?

If there is no DC bias, the average is zero. If there is a DC bias, the average is the DC bias. Somehow, I don't think that's what you are actually looking for, though. Please rephrase your question. Perhaps you mean how do you convert between RMS/peak/peak to peak voltage???What_is_the_conversion_for_rms_voltage_to_peak_to_peak_voltage