0
Providing the power supply is switched off at the mains there is really no problem except for the following :-
# New installations need to conform to part p of the building regulations as does any installation in the kitchen, bathroom or other wet rooms and may need the earth / cross bonding upgrading. # If the wiring in the old light (not the house wiring) is in the old red and black colouring this may suggest that the house wiring itself may have been around for a long time and may need checking.(The house wiring being red and black would not in itself be an indicator and may still be fairly new).
# The original fitting may not have been installed correctly. For example if it is wired into the ring main instead of the lighting circuit then in needs to be connected via an appropriately fused spur. # The term standard hard wired light fixture doesn't give indication of the units loading and may be taking the existing circuit past it's safe capacity. # Any cutting or removal of fire barriers eg plasterboard needs to be protected by intumescent strips or foam. # I am not an electrician and have no vested interest but would suggest that the need to ask the question indicates that you need qualified help in case you've not considered the above or there is some other possibility that I haven't thought of bearing in mind I've never seen the site. # Mains voltage can be and often is lethal.
What else can I help you with?
What is a pin based fluorescent light fixture?
A pin based fluorescent light fixture is the type of fixture that takes fluorescent tubes. On each end of the fluorescent tubes there are contact pins. These pins are used to hold the tube in the fixture and to supply the voltage to the tube from the fixture's ballast.
Can we use a fluorescent lamp in DC?
Yes, fluorescent lamps may be powered by DC but they need a DC lamp controller instead of an AC ballast and starter. The DC lamp controller is more complex. I have a 12V lantern with fluorescent lamp tubes.
How do you wire plunger lamp holder of fluroscent light fixture?
It sounds like you are describing either a slimline or dc recessed base type of fluorescent fixture. There is a wiring diagram on the ballast of both of these types of fixtures. Do your wiring the same as what is shown and you will have no problem.
What causes choke in a fluorescent tube light to burn?
There is a coil which converts ac/ to d/c in some models. Sometimes the insulation fails and the wires gets shorted. The wires are covered with a very thin layer of shellac to reduce the size of the ballast and increase inductance.
4 fluorescent lights won't come on and 2 other fixtures do what causes this?
A. no power to the fixture that won't turn on. B bad electrical connection. c. burned out fluorescent lamps d. bad lamp holders e. bad ballast f. etc.
If the ballast on a fluorescent light blows will the lamp still work?
Typically, if the ballast on a fluorescent light blows, the lamp will not work. The ballast regulates the electrical current to the lamp, so if it is not functioning properly, the lamp will not receive the correct power to light up.
What is the purpose of a fluorescent light ballast and how does it function in the operation of fluorescent lighting systems?
The purpose of a fluorescent light ballast is to regulate the electrical current flowing through the fluorescent light tubes. It provides the initial surge of electricity needed to start the light and then regulates the current to keep the light glowing steadily. The ballast also helps prevent flickering and ensures the longevity of the fluorescent tubes.
Why does fluorescent light flicker?
Fluorescent lights flicker because they rely on a ballast to regulate the flow of electricity. If the ballast is faulty or the light bulb is reaching the end of its lifespan, it can cause the light to flicker.
What is the purpose of the ballast in a fluorescent light fixture?
The purpose of the ballast in a fluorescent light fixture is to regulate the electrical current flowing through the light bulb, ensuring that it operates efficiently and produces steady light output.
How can I change a ballast in a fluorescent light?
To change a ballast in a fluorescent light, first turn off the power to the light fixture. Remove the cover and locate the ballast. Disconnect the wires and remove the old ballast. Install the new ballast in the same position and reconnect the wires. Finally, replace the cover and turn the power back on.
Why is my fluorescent light not working?
Your fluorescent light may not be working due to a faulty bulb, a problem with the ballast, or issues with the electrical connection.
What is the purpose of a ballast in a fluorescent lighting system?
The purpose of a ballast in a fluorescent lighting system is to regulate the electrical current flowing through the fluorescent tube, ensuring that it operates efficiently and produces a steady light output.
What is the process for t12 ballast replacement in a fluorescent light fixture?
To replace a t12 ballast in a fluorescent light fixture, first turn off the power to the fixture. Remove the cover and locate the ballast. Disconnect the wires and remove the old ballast. Install the new ballast, reconnect the wires, and replace the cover. Turn the power back on and test the light to ensure it is working properly.
How can I dim a fluorescent light?
You can dim a fluorescent light by using a dimmable ballast or a dimmer switch specifically designed for fluorescent lights. These devices control the amount of electricity flowing to the light, allowing you to adjust the brightness.
Compact fluorescent lamps have made a lot of changes in the lighting sector it is also changed from a fluorescent lamp to compact fluorescent lamps but still it is dependent on the ballast Why?
A ballast is an electrical component used with a fluorescent bulb (or mercury vapor lamp or arc lamp) to conduct electricity at each end of the tube. Compact fluorescent light bulbs are dependent on ballast because they use a gas to create light. when the gas is excited by electricity, it emits invisible ultraviolet light that hits the white coating inside the fluorescent bulb. The coating changes the ultraviolet light into light you can see.
Can you use a 65 watt fluorescent bulb in a metal halide light fixture?
No, the ballast's output is not matched to operate a fluorescent bulb.
Why is my fluorescent light flickering?
Your fluorescent light may be flickering due to a faulty starter, a defective ballast, or a loose connection. These issues can interrupt the flow of electricity to the light, causing it to flicker.
