0
By Megger testing (meggering) of the motor any one can measure the IR of the motor. MEGGER is a device used to measure IR. Analog Megger device may generate 500 volts..it gives coil to coil or coil to body IR value...it should not be less than 2 Mega ohm, generally it should be or kept more than 5 mega ohm...thanks
...DEEPAK RAJPUT
What else can I help you with?
What is the use of resistance box?
The use of a resistance box or a "Decade Box" is to help calibrate instruments used to measure electrical values such as Voltage, Current, and Resistance. Without them you would not have a known value of resistance to use as a set point.
How is insulation measured?
Floors, attics and walls all require insulation of different R-Values which are measured by the thickness of the insulation. The R-Value determines how well the insulation will resist heat flow. The higher the R-Value the more resistance it has to heat and cold. If you are adding to existing insulation there is another factor to consider. You will have to determine the R-Value of the existing to know how much additional insulation to add
What value does 10 insulation give?
If you are referring to the R value of insulation, then 10 would be the 'thermal resistance' value of the insulation. A value of 10 is about what 3 1/2 inches of fiberglass batt insulation would give you. That is what you might put within your exterior walls if you are using wood studs. The higher the R value the better insulation you will have. When you add up all of the R values of the materials that make up your exterior wall you will get your total value. Depending on where your building is located, and the climate in that area, you will need to adjust your insulation accordingly.
What is magnetoresistence?
The change in electrical resistance produced in a current carrying conductor or semiconductor on application of magnetic field H.
How is electrical resistance decreased?
Ways to reduce electrical resistance: increase the diameter of the conductor, decrease or increase the temperature of conductor (depending on its thermal characteristics), decrease the length of the conductor. A change in the material out of which the conductor is made can decrease resistance, too. And there is the phenomenon of superconductivity. In a simple circuit the resistance can be lowered by adding resistors in parallel. The total circuit resistance will then decrease. You can also reduce resistance by substituting resistors of lower value, or by adjusting a potentiometer, or pot, to a lower value.
How do you test pickup coil on a ATV?
A pickup coil for an ATV may be tested by measuring the resistance across the coil's electrical leads and comparing this value against the expected range specified in the ATV's shop manual.# Disconnect the pickup coil assembly from the ignition system (e.g. the CDI unit or engine control module) # Identify the coil's electrical contacts on the connector # Measure the electrical resistance between the coil's contacts with an Ohmmeter or digital volt meter.Take care not to grab both leads of your ohmmeter with your fingers while measuring this value or you'll measure your body's resistance in parallel with the coil. It's not dangerous but it might corrupt your reading.The value for working part will vary by manufacturer and model, but will typically be between 100 ohms and 350 ohms.If the coil reads as an "open circuit", or the resistance in the high 10's of k-ohms or higher, your coil is damaged and likely non-functional.
What does a megohmeter or megger test?
It checks resistance from a circuit or an electrical component to earth, to make sure it is electrically isolated. This must be a very high value of resistance, hence 'megohms'.
How do you check a resistor?
You can measure directly with an Ohm Meter, often combined with a Volt Meter. Or you can measure the voltage across the resistance and the current to calculate resistance as Current divided by Voltage.
Steel U Value?
The U-value of steel varies depending on its thickness and specific composition. Generally, steel has a relatively low U-value compared to other building materials, which means it has good insulation properties. However, using additional insulation materials along with steel framing can further improve the energy efficiency of a building.
How much energy does insulation save?
it depends on the r-value of the insulation and the area or temperature range of the climate it is to be installed
What is theYamaha XT600E Pickup resistance?
The pickup resistance of a Yamaha XT600E is typically around 100-150 ohms. This value can vary depending on the specific model year and any modifications that have been made to the electrical system.
Is duct tape a good insulator?
Duct tape is not a good insulator. While it can provide some temporary insulation, it is not designed for long-term or effective insulation due to its low R-value and lack of proper sealing properties. It is better suited for temporary repairs or sealing applications.
