0
For a 250 amp welder, a common practice is to use a cutoff switch rated at least 25% higher than the welder's output. This means a cutoff switch rated for around 300 amps would be appropriate to ensure safe operation and handle potential inrush currents. Always consult the welder's manufacturer specifications and local electrical codes for specific requirements.
What else can I help you with?
Can you replace a ksd301g 125v 16a 240 temp switch with a ksd301 125a 10a 250 temp switch?
No, you cannot directly replace a KSD301G 125V 16A 240°C temperature switch with a KSD301 125V 10A 250°C temperature switch. The KSD301G has a higher current rating (16A) compared to the KSD301 (10A), meaning it can handle more current without overheating or failing. Additionally, while the KSD301 has a higher temperature rating, the difference in specifications may affect performance and safety, so using components with matching ratings is crucial.
A DC voltmeter has a resistance of 20000 ohms per volt What is the resistance of the meter if the range selection switch is set on the 250 volt range?
5 megohms
How many 250 kcmil cable in 5 inch conduit?
ONE
How many amps can a 250 va transformer carry?
A transformer is a power source. It will provide voltage to a device. Find the voltage rating on the device, say 24V. 250/24 = ~10A.
How many amps is 250 MCM wire good for?
300 Amps if used for service entrance conductors. Table 310.15
Where is the automatic fuel pump cutoff switch on a 86 ford F-250?
Hmm, did you look along the firewall?
An arc welder provides 250 A of current when operating with a voltage of 40 V what is the power dissipated by this welder?
10,000 Watts
What is the value of Lincoln welder ac 250 c?
That would depend on the model , age and condition or hours .
Can you tig with 250 dialarc welder?
Yes, you can TIG weld with a Dialarc 250 welder, as it is capable of delivering the necessary amperage for TIG welding. However, you will need to use a suitable TIG torch and gas setup, as the Dialarc is primarily an arc welder. Ensure you have the appropriate gas supply and tungsten electrode for the materials you are welding. Proper setup and technique will help achieve good results.
Will a yz 250 engine fit in a yz 125 frame?
No a 125 frame is too small to fit a 250 motor but with a cutting torch and a welder anything is possible.
If a welder is qualified to multiple qualification on 12.750 250 pipe under api 1104 can he roll out weld a 20 500 weld?
No, a welder qualified under API 1104 for 12.750 250 pipe cannot automatically roll out weld a 20 500 weld. Each welding procedure qualification (WPQ) is specific to certain variables, including pipe diameter and wall thickness. The welder would need to demonstrate qualification for the new pipe specifications to ensure compliance with safety and quality standards.
How do you replace the ignition switch on a 1996 ford f-250 without a key?
You drill out the exsisting ignition switch!!
How do you remove the headlight switch on 2008 f-250 ford?
Remove the knobs, remove the dash panel, and replace the switch.
Where is the neutral safety switch on a 1984 Ford F-250?
how do you mount a safty switch on the clutch 84 ford f250
How do you repair the F 250 super duty mirror will not adjust using the mirror adjustment switch?
switch wiring or mirror it's self probly switch
Can you use a 250 watt bulb with a 15 amp switch?
Yes, you can use a 250 watt bulb with a 15 amp switch. The switch is rated for up to 15 amps, which is more than enough to handle the power of a 250 watt bulb. Just make sure that the wiring and other components in the circuit can also handle the load.
How many hundreds in 25000?
250 of them.
