answersLogoWhite

0

On wiring a house it is common practice to have other circuits in the wall cavity passing by the built in shower stall. Electrical outlets that face outward from the shower stall wall that service another room is also common practice. There is no danger from electrical shock as the shower is isolated from the wires by wall board and usually ceramic tiles that make up the shower stall or in some cases a fiberglass shower enclosure.

Do you mean inside the shower area, or outside the shower area?

It is never safe to have any electrical outlets:
  • inside a shower cubicle
  • next to a bath
  • next to a sink
  • next to a hand wash basin
  • in any other kind of wet area

There are very strict wiring codes and regulations about where you can place a socket outlet. IF YOU ARE LOOKING FOR INSTRUCTIONS HERE

BECAUSE YOU NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY

YOU MUST CALL IN A LICENSED ELECTRICIAN

TO DO IT FOR YOU.

ANSWER

If your question should be read as "Is it safe to have electrical outlets on the other side of a wall to a shower area, such as in a dry room like a bedroom, etc., normally the answer would be Yes, but it is best to check with a licensed electrician to be sure. Always be sure to switch off the breakers at the main panel before you attempt to do any work on any mains power circuit.

--------------------

This is something I wondered when I gutted my fiberglass shower enclosure and noticed that there was an electrical box behind one of the walls servicing a hall light switch and yet another box on the back wall behind the shower enclosure serving the light fixture and exhaust fan to the master bath. It doesn't feel right to have electrical so close to water. In my townhouse they only used gypsum board behind the fiberglass enclosure with no plastic vapor barrier. So, I have to think about how to remodel the shower with these two electrical boxes in the mix.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

What is the best way to remove drywall?

The best way to remove drywall is to start by cutting the drywall into manageable sections using a utility knife or drywall saw. Then, use a pry bar or hammer to carefully remove the sections from the wall. Be sure to wear protective gear and be cautious of electrical wiring or plumbing behind the drywall.


What are the necessary steps for installing a drywall electrical box?

To install a drywall electrical box, first mark the location on the wall, then cut a hole in the drywall. Next, insert the electrical box into the hole and secure it in place. Connect the electrical wires to the box according to the wiring diagram. Finally, attach a cover plate to the box to complete the installation.


How can I cut outlet holes in drywall?

To cut outlet holes in drywall, use a drywall saw or utility knife to carefully trace the outline of the electrical box onto the drywall. Then, cut along the traced lines, making sure to cut slightly smaller than the outline to ensure a snug fit for the outlet. Be cautious and precise to avoid damaging the drywall or electrical wiring.


What are the potential risks or concerns associated with finding metal behind drywall during a renovation project?

Potential risks or concerns associated with finding metal behind drywall during a renovation project include electrical hazards if the metal is wiring or conduit, structural issues if the metal is a support beam or stud, and potential injury from sharp edges or rust. It is important to proceed with caution and consult a professional if unexpected metal is discovered during renovation work.


Saving Walls with Drywall Access Doors?

< p> By placing drywall access doors over vital areas in one�s home such as over electrical wiring or plumbing, it allows easy access to those areas without having to force demolition of drywall. Proper placement of these doors can save a homeowner time and money. Drywall access doors can also be used to hide important things such as security system wiring or water valve controls. These doors can also be installed in ceilings as well to allow access to conduits, wiring for lights, and air vents. < /p>


What is concealed wiring?

Concealed wiring is wiring that can not be seen. A good example of this is house wiring that is located behind the wall board. The word concealed gets mentioned in the electrical code. It states, that any concealed wiring cannot be covered until the electrical inspector or one of his representatives checks to make sure that the installation is safe to cover.


How can I locate wiring in walls?

To locate wiring in walls, you can use a stud finder with a built-in electrical scanning feature. This tool can detect the presence of electrical wiring behind the walls. Additionally, you can also use a non-contact voltage tester to identify live wires without having to physically touch them. It is important to exercise caution and follow safety guidelines when working with electrical wiring.


What is electrical wiring connection in domestic house in India?

domestic electrical wiring designig


Is conduit required for basement electrical outlets?

Conduit is not always required for basement electrical outlets, but it can provide added protection for the wiring and enhance safety. Checking local building codes and consulting with a qualified electrician is recommended to determine the specific requirements for your location.


Where can you find wiring diagram for carrier ac unit model unit 40aq036330?

Behind the panel that covers up the electrical section has one


What are some specialties to do in construction?

Construction specialties include framing, roofing, plumbing and electrical wiring. Additional specialties may be HVAC people who install the heating and cooling systems, or cabinet making, drywall finishing or painters.


Is the white wire hot in electrical wiring?

No, the white wire is typically neutral in electrical wiring, not hot.