0
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
What else can I help you with?
How do you install a dimmer switch for multi fixtures where the original switch has 2 black wires and one red with no green?
This simple if you have two switches controlling a set of light you will need to buy a three way switch. A three way switch will have a place for three connection. Depending on what brand of switch you purchase the directions will be sightly different but most dimmer come with detailed directions and diagrams. When you by a dimmer you need to read what kind of load it is meant to control. They are built to control incandescent light, magnet low voltage lights or electronic lights.
I am removing a dimmer switch to put in a regular switch but there are two incoming hot wires what do i do?
The regular switch just connects in the circuit the same way as the dimmer switch came out. If the dimmer switch had its own wires the only difference will be is you will have to supply your own wires from the new switch to the existing connection. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
How do you wire a 3 way dimmer switch that has two black wires and one green?
You need to first determine where wires go. If you Google 3 Way Switch you can get a diagram. Each switch has 3 contacts.. Think about a kids teeter totter. Each end represents a switch contact and the center is a common point. You connect the ends to either end on the 2nd switch. The common contact on one switch goes to supply power hot side and on the other switch the common point goes to the load. Then the neutral of supply connects to the load neutral and the supply ground connects to the ground of the load.
Is it possible to run power from a three way switch to install an outlet?
Yes you just have to "steal" power from the switch. Do this by running a pigtail wire from the hot of the switch to the hot wire of the plug. Make sure you do this before the switch or you will end up with your outlet being switched as well.
How do you install an intermediate switch with 2 two-way switch?
Click the link and watch a video I have posted showing exactly how to wire this configuration.
How do I properly wire a 2-way dimmer switch in my home?
To properly wire a 2-way dimmer switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and connect the dimmer switch's wires to the corresponding wires in the wall. Typically, this involves connecting the black dimmer wire to the hot wire, the green wire to the ground wire, and the red or white wire to the load wire. Secure the connections with wire nuts and mount the dimmer switch in the wall box. Turn the power back on and test the dimmer switch to ensure it is working properly.
How do I properly wire a three-way dimmer switch in my home?
To properly wire a three-way dimmer switch in your home, you will need to follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire, traveler wires, and ground wire. Connect the common wire to the black wire on the dimmer switch. Connect the traveler wires to the other two wires on the dimmer switch. Connect the ground wire to the green screw on the dimmer switch. Secure the dimmer switch in place and turn the power back on to test the dimmer. It is important to follow the manufacturer's instructions and consult a professional if you are unsure about any step in the process.
How do you properly wire a dimmer switch in a 2-way configuration?
To properly wire a dimmer switch in a 2-way configuration, you need to connect the hot wire from the power source to the common terminal of the dimmer switch. Then, connect the traveler wires from the existing switch to the traveler terminals of the dimmer switch. Make sure to follow the manufacturer's instructions and turn off the power before starting the wiring process.
How do you wire a 3-way dimmer switch?
To wire a 3-way dimmer switch, you need to connect the common wire from the dimmer to the common wire in the electrical box. Then, connect the traveler wires from the dimmer to the traveler wires in the box. Make sure to follow the manufacturer's instructions and turn off the power before starting the installation.
How can I properly wire a 2 way dimmer switch in my home?
To properly wire a 2-way dimmer switch in your home, follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch from the wall. Identify the common wire, traveler wires, and ground wire. Connect the common wire to the common terminal on the dimmer switch. Connect the traveler wires to the other terminals on the dimmer switch. Connect the ground wire to the ground terminal on the dimmer switch. Secure the dimmer switch in the wall box and turn the power back on to test the switch. It is recommended to consult a professional electrician if you are unsure about any step in the process.
How to wire a 3-way dimmer switch correctly?
To wire a 3-way dimmer switch correctly, you need to connect the common wire from the dimmer to the common wire in the electrical box. Then, connect the traveler wires from the dimmer to the traveler wires in the box. Make sure to follow the manufacturer's instructions and turn off the power before starting the installation.
How can I install a three-way dimmer switch in my home?
To install a three-way dimmer switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire. Connect the common wire to the common terminal on the dimmer switch. Connect the other two wires to the remaining terminals on the dimmer switch. Secure the switch in place and turn the power back on to test the dimmer.
How do I go about installing a 3-way dimmer switch in my home?
To install a 3-way dimmer switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire. Connect the common wire to the common terminal on the dimmer switch. Connect the other two wires to the remaining terminals on the dimmer switch. Secure the switch in place and turn the power back on to test the dimmer.
How can I install a 3-way dimmer switch in my home?
To install a 3-way dimmer switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire, traveler wires, and ground wire. Connect the common wire to the common terminal on the dimmer switch, and the traveler wires to the other terminals. Connect the ground wire to the ground terminal. Secure the switch in place and turn the power back on to test the dimmer.
How can I properly wire a three way dimmer switch according to the wiring diagram?
To properly wire a three-way dimmer switch according to the wiring diagram, you will need to identify the common wire, traveler wires, and ground wire. Connect the common wire to the black screw on the dimmer switch, and the traveler wires to the brass screws. Make sure to connect the ground wire to the green screw on the switch. Follow the wiring diagram carefully to ensure correct installation.
How can I properly wire a 3-way dimmer switch in my home?
To properly wire a 3-way dimmer switch in your home, you will need to follow the manufacturer's instructions carefully. Typically, you will need to identify the common wire, traveler wires, and ground wire. Connect the common wire to the black screw on the dimmer switch, and the traveler wires to the other two screws. Make sure to turn off the power before starting and test the switch before finishing the installation.
How do I properly wire a Lutron 3-way dimmer switch?
To properly wire a Lutron 3-way dimmer switch, you need to connect the wires according to the instructions provided by Lutron. Typically, you will need to identify the hot wire, traveler wires, and ground wire, and connect them to the corresponding terminals on the dimmer switch. It is important to turn off the power before starting the installation and follow all safety precautions.
