0
transistor sl 100n has 3 pins and it is work like a switch. there is metal lead in the above metal surface the nearest pin is emeter and last pin is collector and center pin is base
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is Pin configuration of transistor sl100?
The pin configuration of sl 100 is B C E with ground as the base of the transistor.
What is pin diagram of IC L293D?
What enable1&enable2 in pin l293d
What is the emitter base collector in 2N5777 photo transistors?
1st pin is emitter then collector and base
How many transistors inside of a microprocessor can fit on the head of a stick pin?
7 , nah im kidding, what sorta question is that lol
Can you replace a npn transistor by a pnp transistor?
Think of it this way: "P" is for Positive and "N" is for Negative So basically put a PNP Transistor Would use N to Switch P, in the name "PNP" or "NPN" the first character is for the polarity of the Collector-pin, the second for the Base-Pin, and the third for the Emmiter-pin. If you have a NPN Transistor you can`t just replace it with an PNP as the polarities differ. If you can find a way to change those polarities then sure it could work. I would say it`s best go out and buy a few of both so you have a few, otherwise if the application of the transistor is not in a high-current or high-voltage circuit try and find another circuit with the required type of transistor. Absolutely most transistors can be replaced with other similar transistors. Different transistors have different conditions they work by so you should do some research and replace it with another that is either the same or have approximately the same data. Example 1: A burned transistor with the data NPN, 45Volt, 100mA, 0,3Watt, need to be replaced. It is a discontinued transistor, so unfortunately no original spare part can be found. Check the max voltage of the circuit where it was. If the voltage is close to 35 volt, then you may want to replace it with a higher voltage transistor. If it is lower, say max 20 Volt, then you should be able to replace it with a lower voltage transistor. Check the type of circuit where it was. If in an audio amplifier, then you should choose a 'low noise' audio transistor. Look at the NPN transistors you can get hold of and make your choice based on similar or more current, similar or more wattage, similar or lower or even higher voltage. Most small signal transistors are interchangeable if you follow these steps. Even most power transistors are interchangeable but you should make an extra effort and check/match the HFE Data on the transistor too. Normally no need for an exact match at all.
What is Pin configuration of transistor sl100?
The pin configuration of sl 100 is B C E with ground as the base of the transistor.
What is pin diagram of IC L293D?
What enable1&enable2 in pin l293d
Where can you get 6845 pin diagram and block diagram?
ni mooti lo
What is the emitter base collector in 2N5777 photo transistors?
1st pin is emitter then collector and base
How many transistors can be placed on the head of a pin with a 1000 micron radius?
890 and three thousandths
Explain the pin diagram of Pentium processor?
i dnt know
How many transistors inside of a microprocessor can fit on the head of a stick pin?
7 , nah im kidding, what sorta question is that lol
How will be the pin diagram to interface adc to pic?
It depends on the ADC and PIC
4 pin round wiring diagram for trailer?
here you go
Btech 4-2 ECEquestion papers?
Draw the pin diagram of 8051 and explain the functioning of each and every pin.
Where can you find a download able radio wiring diagram pin diagram for a 2007 Ford Expedition with factory amp?
sfn
Where can i find a wiring diagram and wiring harness pin diagram for a 95 Chevy silverado?
for the ECM, sorry i left that part out
