0
What else can I help you with?
Line following robot using pic 16f877a?
4eyes
How do you deal safely with a wire dangling from an electric line?
Remain clear of the wire that is hanging from an overhead line and get in touch with the distribution's utility company immediately. They have the proper safety equipment to deal with situations like this.
What is meant by single line diagram?
Single sine diagram is graphical representation of electrical circuit drawn using single line instead of drawing 3 separate lines for three phases.
Draw logic diagram of two to four line decoder using nor gates only with enable input?
draw logical diagram 2 to 4 line decoder with nor gates only
What is LILO in electrical transmission?
LILO is Line In Line Out. If a new EHV substation is inserted between two existing substaions, the transmission line for new inserted EHV substation is called LILO i.e. Line In Line Out. When a transmission line is passing nearby to a substation or generation station to tap it, the system used is called LILO. While using this system , one bay is required for incomer and the other is outgoing. The power is drawn or added as per requirement. It may also be called Loop In Loop OutSP.
How hot can a Line Bender Get?
A line bender can get over 200 degrees :P
What is line bender?
A line bender is a manufacturing process in which a plastic part is heated, softened, bent to a desired shape, and then cooled to hold that shape.
Where should you stop at an intersection to ensure safety and follow traffic rules?
When approaching an intersection, you should stop behind the stop line or crosswalk to ensure safety and follow traffic rules.
Using 12 inch EMT and a hand bender you want to make a bend with a 14 inch stub up How far from the end of the conduit should you put the mark that will line up with the bender arrow?
1/4"
How do you use a line bender?
Only almighty God knows that!
If you disregard safety rules what can OSHA do to you?
If you are a supervisor or manager acting as a representative of the management of your company when you disregard safety rules enforceable by OSHA, OSHA can fine your company and issue citations. If your disregard results in the death of an employee, OSHA can recommend that the Federal Attorney file criminal charges against your or your company. If you are an employee but not acting as a manager of your company when you disregard safety rules that are enforceable by OSHA, OSHA can cite your employer and impose fines on your employer for failure to require you to follow the safety rules. Bottom line, if you disregard safety rules, accidents will happen that will cause health and safety risks - injuries and fatalities and you will definitely get a lawsuit out of it.
Can you bring all dogs to the bluebell railway line?
No, it is not safe or appropriate to bring all dogs to the bluebell railway line. It is essential to follow rules and regulations regarding pets in public areas to ensure their safety and the safety of others.
How did chief bei fong get her scar in The Legend of Korra?
Chief Lin Beifong received the scar when she attempted to arrest her sister using metal bending. Her sister, also a metal bender, cut the metal line that Lin was using and the tension in the line caused the metal to whip backwards, hitting Lin in the face and causing the scars.
How to properly ground a gas line for safety measures?
To properly ground a gas line for safety, you should connect a grounding wire to the gas line using a grounding clamp. This helps prevent the buildup of static electricity and reduces the risk of sparks that could ignite gas leaks. It is important to follow local building codes and regulations when grounding a gas line to ensure proper safety measures are in place.
Why are rules given?
Rules are given to keep people in line. If there were no rules, then there would be absolute CHAOS!
What kind of fouls are there in polo?
Most fouls revolve around the safety of horse and rider. The rules revolve around protecting the "line of the ball" and the "right of way". Hope this helps! Lauren
What is a line bender?
a heat strip heats up and u place the plastic on the strip and you leave it until its melted or softened and you form it into a shape you want then you cool it or let it cool on ots own
