0
What else can I help you with?
If as more resistors are connected in series with the first what happens to the potential difference across each resistor?
adding resistors to a string will have the effect of decreasing each resistor voltage drop.
What happens if you remove emitter resistor in RCcoupled amplifier?
what happens if we remove Rc in RC coupled amplifier
What does a pre-set resistor do in a circuit?
A preset resistor is used in some circuits to change the resistance. The preset resistor enables the circuit to be more or less sensitive thereby altering the resistance.
What happens to current in a parellel circuit if a resistor load increases?
Your question needs rephrasing; as it stands, it makes no sense.
How dimer switsh work?
It works by sending the current through a resistor. As you twist the dimmer switch it changes the length of the resistor and the longer the resistor the more it inhibits the current. So at full brightness the resistor has been totally bypassed as you turn the light down the contact moves further around the resistor making it longer.
What happens when more than one resistor is connected to a circuit?
the current flowing in will be low
If as more resistors are connected in series with the first what happens to the potential difference across each resistor?
adding resistors to a string will have the effect of decreasing each resistor voltage drop.
What are components in smart chip?
capacitor,transistor,resistor,inductor
What happens when you use a smaller resistor in place of larger one?
as we can deduce from its name, the resistor "resists" to the current (the movement of the electrons) so as the value of the resistor increases, the current flowing through it decreases. so when you use a smaller resistor, the current increases, however the tension between its poles decreases ( due to the voltage divider law). remember that the shortcircuit is due to the small value of the current , so we need always to have a resonable resistance on the circuit..... but not too high because joule losses we'll be more significant !! hope i've been clear :D
How do you connect resistor?
In a circuit, either in Parallel or in Series with other components.
What happens to the resistance of a common ohmic resistor when it is heated?
When a common ohmic resistor is heated, its resistance typically increases.
What are the components of a resistor?
Resistance is the property of a component which restricts the flow of electric current.
When resistors are connected in series then what happens to the watt?
Resistors are rated in wattage so the lowest wattage rating will be the wattage of the series circuit. It will be able to handle that power any more and the lowest wattage resistor could be damaged and fail.Another AnswerWhen two or more resistors are connected in series, the resistor with the lowest resistance will operate at the highest power. If the power developed by a resistor exceeds its rated power, then the resistor may burn out.
What is the basic of electronics components?
The most Basic or Simple electronic component is the resistor capacitor.
What is the lifespan of a resistor?
A resistor doesn't deteriorate with age, and has no particular 'life-span', as long as it's used properly. -- A resistor in a box on the shelf, or in a circuit where it stays cool, will last indefinitely. -- A resistor in a circuit where it's forced to dissipate enough power to make it hot may change its resistance value permanently, but will continue to operate. -- A resistor in a circuit where it's forced to dissipate even more than that, to a ridiculous extreme, may melt or explode. When that happens, it's the end of the resistor's life-span. But it wasn't the resistor's fault.
What is the voltage drop through resistor 1?
There is insufficient information in the question to properly answer it. You don't state the value of resistor 1, nor do you state how it is connected in the circuit, nor do you state the value of the other components in the circuit. Please restate the question, giving more details.
How to add a capacitor and resistor in parallel?
To add a capacitor and resistor in parallel, simply connect one terminal of the capacitor to one terminal of the resistor, and then connect the other terminal of the capacitor to the other terminal of the resistor. This creates a parallel circuit where both components share the same voltage.
