0
What else can I help you with?
Need wire a up and down switch?
To wire an up and down switch, first ensure that the power is turned off at the circuit breaker. Connect the common terminal of the switch to the power source, then wire the up switch to one terminal and the down switch to another terminal, ensuring that the appropriate wires are connected to the load (e.g., motor or actuator). Finally, double-check all connections for safety and secure the switch in its housing before restoring power.
What is a device comprising both a transmitter and a receiver which are combined and share common circuitry or a single housing?
radio
What is IC housing for recessed lighting?
IC recessed fixtures can be covered with insulation. Since insulation can be in direct contact with the fixture housing they reduce energy loss. The old type fixtures had to have a box of non combustable material built over the fixture for fire-proofing. Recessed fixtures have come a long way.
What causes an electric motor body to give an electric shock when a person touches it and the ground together?
That condition is called a "ground fault". That's when the insulation of the motor winding has a break somewhere, allowing current to leak to the motor housing. The motor SHOULD be grounded, protecting the user from electrical shock, but many older motors were not grounded, providing the potential for just this type of condition. Newer motors are often "double insulated", meaning that not only is the motor winding insulated, the motor housing is also insulated. Often the housing of a double insulated motor is made of a type of plastic.
What is the best suitable component for circuit protection instead of fuse?
circuit breaker, or "resettable fuse", which is a reallya small circuit breaker in the housing of a fuse
How do you use a wire terminal removal tool?
To use a wire terminal removal tool, you insert it into the connector housing until it latches onto the terminal you want to remove. Then, gently pull the tool and the terminal out of the connector housing. Be sure to follow the specific instructions that come with your particular removal tool for best results.
How do you unplug 2005 Jeep Wrangler blower motor resistor?
Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch . Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor. Remove the two screws that secure the blower motor resistor block to the HVAC housing. Remove the resistor block from the HVAC housing............
How do change the starter on a 2000 Dodge Durango?
== # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nut and the lock washer that secures the lower mounting flange of the starter motor to the stud on the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the screw and washer (rearward facing) that secures the lower mounting flange of the starter motor to the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer (rearward facing) that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the hole in the starter motor lower mounting flange over the stud on the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket rearward on the tubes and into position over the starter motor upper mounting flange. # Loosely install the screw and washer unit that secures the starter motor upper mounting flange to the automatic transmission torque converter housing. # Loosely install the lock washer and nut that secures the starter motor lower mounting flange to the stud on the automatic transmission torque converter housing. # Tighten the screw and washer unit and the nut that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screw and the nut to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable. == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the starter motor mounting flange on the automatic transmission torque converter housing and loosely install the two screw and washer units to secure it. # Tighten the two screw and washer units that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screws to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable.
How do you change a starter on a 2005 Dodge Dakota?
# Disconnect and isolate negative battery cable. # Raise and support vehicle. # Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt. # Remove one bolt and one nut if equipped with a manual transmission. # Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor during this process, do not let starter motor hang from wire harness. # Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness. # Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud. # Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle. # Remove starter motor.# Disconnect and isolate negative battery cable. # Raise and support vehicle. # Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt. # Remove two bolts if equipped with an automatic transmission. # Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor during this process, do not let starter motor hang from wire harness. # Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness. # Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud. # Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle. # Remove starter motor.# Connect solenoid wire to starter motor (snaps on). # Position battery cable to solenoid stud. Install and tighten battery cable eyelet nut . Do not allow starter motor to hang from wire harness. # Position starter motor to transmission. # Install and tighten lockwasher nut and bolt . # Lower vehicle. # Connect negative battery cable.# Connect solenoid wire to starter motor (snaps on). # Position battery cable to solenoid stud. Install and tighten battery cable eyelet nut . Do not allow starter motor to hang from wire harness. # Position starter motor (4) to transmission. # If equipped with automatic transmission, slide cooler tube bracket into position. # Install and tighten both bolts . # Lower vehicle. # Connect negative battery cable.
Where is the single wire in-line SPOUT connector on a 1989 Bronco II 2.9 liter fuel injected engine?
follow the wiring harness towards the pass. side of the engine compartment from the distributor,it only leads to one thing!!! If you have an A/C equipped model like I do, the SPOUT connector is right up against the evaporator housing on the engine side, hanging out of a wire harness. It's a black connector shell with 2 short yellow/green wires on one end, and a removable plug on the other. It's taped to the side of the harness, but not wrapped in it.
1995 Nissan Sentra blower motor resistor installation?
Locate the resistor under the dash attached on the blower motor housing. Disconnect the wire harness connector. Remove the resistor and install a new one.
Where is the speedometer sensor on a 1996 Volvo 850 GLT?
It is inside the electrical plug at the transmission. You need to remove the battery, battery shelf, complete air cleaner housing and bracket. Once you unbolt the electrical connection you need to remove the the sockets from inside the connector housing then you can split the sockets. The speed sensor is the socket at the top of the housing (furthest away from the incoming harness)
How do you replace an ect sensor on a Mazda 6 2003?
To replace the ECT (Engine Coolant Temperature) sensor on a 2003 Mazda 6, first, ensure the engine is cool and disconnect the negative battery terminal. Locate the ECT sensor, which is usually found near the thermostat housing. Remove the electrical connector and unscrew the sensor using a wrench. Install the new sensor, reconnect the electrical connector, and reattach the battery terminal.
How do you change temperature sensor on 2005 Dodge Magnum?
To change the temperature sensor on a 2005 Dodge Magnum, first ensure the engine is cool and disconnect the negative battery terminal. Locate the coolant temperature sensor, which is typically positioned near the thermostat housing. Remove the electrical connector, then unscrew the sensor using a socket or wrench. Install the new sensor, reconnect the electrical connector, and reconnect the battery terminal.
Where is the ODB2 connector on a Ford F450?
The Ford F450 OBD connector can be found on the top of the engine. The ODB connector will be near the air intake housing.
How do I replace the TPS in my 93 Chevy Lumina?
its easy it a sensor between the air filter housing and the throttle body with a wire harness connector on it. It shold be attached by 2 little torques head (kind of looks like a star) screws
How do you replace headlight housing on 2003 Nissan Xterra?
To replace the headlight housing on a 2003 Nissan Xterra, first, disconnect the negative battery terminal to ensure safety. Remove the screws or bolts securing the headlight assembly, usually located at the top and side of the housing. Gently pull the assembly forward, disconnect the wiring harness, and then remove the old housing. Install the new headlight housing by reversing these steps, ensuring all connections are secure before reconnecting the battery.
