0
208V is one standard in the US for light commercial 3-phase power. It measures 208V phase to phase and 120V phase to neutral. 230 (or 240)V refers (in the US) to the common service supplied to residential. It is single-phase, with two hots and a neutral; 120-0-120. One hot and the neutral (120V) is used for receptacles and small appliances, both hots (240V) are used for large appliances, such as stoves, ovens, air conditioning, and water heater.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the relationship between peak rms and average values of an ac voltage?
Peak voltage of an AC voltage is the value at its highest or lowest point.RMS (Root Mean Square) voltage of an AC voltage is a mathematical derivation involving the square root of the average value of the squares of samples of the voltage as the sample interval approaches zero.Average voltage is simply that - the average or mean voltage.For a true sine wave, RMS and average are equivalent, but they are not equivalent when the wave is distorted, or has some other shape such as triangular.RMS is the best way to measure an AC voltage, as it gives you a true reading of the amount of power that the voltage can deliver.One issue with non-RMS AC meters is that they typically measure the rectified, filtered peak value and then compensate by dividing by 1.4. This is not correct unless the voltage is a sine wave.AnswerThe peak value of an a.c. voltage or current is the amplitude of that voltage or current waveform -i.e. the maximum value of voltage or current in either the positive or the negative sense.The root-mean-square (rms) value of an a.c. voltage or current. For a sinusoidal waveform, the rms value is 0.707 times the peak value (amplitude). A.C. voltages or currents are always quoted in rms values unless otherwise specified.The average value of an a.c. voltage or current is zero over one complete cycle so, when used, it applies only over one half cycle. Therefore, the average value for one-half cycle of a sine wave is 0.637 times the peak value. Average values are of little relevance to a.c. calculations.
What is RMS Peak value and average value?
RMS is used to determine the average power in an alternating current. Since the voltage in an A/C system oscillates between + and -, the actual average is zero. The RMS or "nominal" voltage is defined as the square root of the average value of the square of the current, and is about 70.7% of the peak value.************************************************************The r.m.s. value of an alternating current or voltage is the value of direct current or voltage which produces the same heating effect.Fo a sine wave, the r.m.s. value is 0.707 x the peak value.The average value is different; for a sine wave it is 0.636 x the peak value.
The effective value of ac voltage is calculated as?
EFFECTIVE HOW ABOUT AVERAGE .639 of peak.AnswerThe 'effective' value of an a.c. voltage (or current) is the same as its 'root-mean-square' (r.m.s.) voltage which, for a sinusoidal waveform, is 0.707 Umax.The 'average' value of an a.c. voltage (or current) is zero over a complete cycle, or 0.639 Umax, over half a cycle (usually applied to rectified waveforms).
When a 3.3V zener diode and a 5V zener diode are connected in parallel what is the average reverse break down voltage?
There will be no "average" reverse breakdown voltage. When the applied voltage reaches 3.3v, the 3.3v zener will conduct and the voltage will go no higher. The 5v zener will never conduct because the voltage across it will never go higher than 3.3v The only way the 5 volt zener will ever conduct is if the 3.3v zener fails. ALAN H.
What is the voltage used for ignitor in boiler?
It really depends on the size but the average is about 24 volts.
What is average voltage?
Another name for average voltage is the RMS (Root Mean Square). This is a voltage derived from the peak to peak voltage multiplied by .707. If the peak to peak voltage is 170 volts then the average voltage (RMS) would be 170 x .707 = 120 volts.
What mathematical formulas is used to find the average value voltage for an ac voltage?
The RMS value of an AC voltage is VRMS = VPEAK / sqrt(2), where VPEAK = the voltage peak to neutral.AnswerThe average value of a sinusoidal a.c. voltage is zero.
What is the average voltage of an electromagnet?
a magnet does not have any voltage, only a magnetic field.
What is the ratio of rms load voltage to mean load voltage?
The mean load voltage, in other words the average voltage, is zero in an ac system.
When It is required to calculate average voltage and when RMS voltage?
It is usually required in electrical examinations to make calculations. Simple answer to a complicated calculation. Remember, take peak to peak voltage and multiply by .707, the result being average voltage. This is the voltage that electrical test meters read.
What is the average amount of voltage in the average Australian home?
1000000 volts
What is average value in alternate voltage?
The term is 'alternating voltage', not 'alternate voltage'. For an a.c. voltage or current, the average value is taken over half its wavelength because, over a complete wavelength it is, of course, zero. For a sine wave, the average value (over half a wavelength) is 0.637 Vmax or 0.637 Imax.
Is DC voltage and average voltage same?
no, dc volatage is a type of current direct current, ac is alternating current, average voltage could be any type of voltage ac or dc that maintains a constant rangeAnswerNo. A DC voltage is exactly equivalent to an AC rms-voltage. So, for example, 100 V (DC) is exactly equivalent to 100 V (AC rms). The average value of an AC waveform is zero.
What is the average voltage in a small potato?
Their is no specific answer because of the shape of potato the average can be .85
How many voltage in thunder?
Lightening1-6 billion volts, 1 average. Thunder is sound waves only and has no voltage.
The energy of electrons at the negative terminal of a battery is called?
I am not entirely sure what you mean, but the average energy per electron is called the voltage, and is measured in units of volts.I am not entirely sure what you mean, but the average energy per electron is called the voltage, and is measured in units of volts.I am not entirely sure what you mean, but the average energy per electron is called the voltage, and is measured in units of volts.I am not entirely sure what you mean, but the average energy per electron is called the voltage, and is measured in units of volts.
Does digital voltmeter measures rms voltage or peak to peak voltage or average?
Yes, most DMM are ''average responding", giving accurate rms reading if the ac voltage signal is a pure sine wave. They measure the average of the absolute value of ac voltage and are calibrated so that reading are corrected to that of the rms value of a sine wave.Error occur if harmonic are present.
