0
Presumably you are asking about the rated secondary current of a transformer rated at 2200 kV.A?
This depends on the rated secondary voltage. You divide the rated apparent power of the transformer by the rated secondary voltage.
Of course, the actual current depends on the load.
What else can I help you with?
Eddy current in transformer?
Yes, a transformer has eddy currents.
How does current transformer works in a substation?
A current transformer works on the same principle as that of a simple transformer however it steps down the high current into a low level so that it can be measured using an ammeter of a suitable range. In some current transformers extra cores are provided. This is done in order to prevent the faulty currents i.e. the over currents, earth faults, differential protections. The extra cores of a C.T. gets saturated as soon as the faulty currents starts flowing and thereby does not harm the main core of the transformer and the ammeter connected. The C.T. is always connected in the line carrying current. It first steps down the current to a measureable form and further gives this current to the ammeter.
What is the function of the primary current when the secondary winding of the transformer is open?
When the secondary of a transformer is opened, there is no longer any load on the transformer. There will be some current flowing in the primary winding, which is needed to induce the voltage in the secondary. This primary current is referred to as the "no load" current, and is indicative of the core losses in the transformer.
What is mean by magnetizing current of transformer?
A: As current flow in the primary it will magnetize the core of the iron in the transformer that is called magnetizing.
How many amps does a 600 watt low voltage transformer box pull?
The transformer itself does not pull current. Whatever you connect to the transformer pulls current. Whatever the output voltage of the transformer is, divide that into 600 and you get maximum current possible without burning up the transformer. At 24V that's 25 amps.
What usually happens at consumer end when the current carrying capacity of transformer is exceeded?
What should happen is that the circuit-breaker should trip to cut off the current before the transformer becomes damaged by overheating.
How is current controlled in welding transformer?
in welding machine, the transformer used is basically a current transforrmer. so by changing the tap of secondary side of transformer, we can increase or decrease the current in the transformer.
What is principle of Current transformer?
why does have to short-circuit secondary wire of current transformer ?
Difference between potential transformer and current trasnformer?
The difference between current transformer and potential transformer is that the secondary of a current transformer can not be open circuited while under service whereas that of the potential transformer an be open circuited without any damage to the transformer.
What is zero current transformer?
It is a transformer with No load attach to it.
What is the current carrying of an 1000kVA transformer?
You cannot answer this question without knowing the rated secondary voltage. Once you know this, divided the voltage into the volt ampere rating.
What is the reason for using a neutral current transformer on a transformer?
A current transformer is primarily used at the neutral point of a transformer for earth fault protection. A neutral current transformer will measure any ground fault current which will essentially flow from the star point of the transformer. A fault-detection device other devices is connected to the current transformer and, if the fault current exceeds a certain trigger value, the fault-detection device will give a trip command to an earth-fault relay to disconnect the supply of electricity to the transformer.
A transformer can only the voltage of an alternating current?
A transformer can only increase or decrease the voltage of an alternating current, and it is called step-up transformer or step-down transformer accordingly.
What is the conditon to connect a DC supply in primary of transformer?
Dc voltage level should not exceed the current carrying capacity of the winding. since winding resistance is very small. We need to be careful in giving the dc voltage to transformer winding.
Eddy current in transformer?
Yes, a transformer has eddy currents.
What is the name of the device that changes the ratio of a current in voltage?
A transformer. it steps up / down voltage, and steps down / up current.
How does current transformer works in a substation?
A current transformer works on the same principle as that of a simple transformer however it steps down the high current into a low level so that it can be measured using an ammeter of a suitable range. In some current transformers extra cores are provided. This is done in order to prevent the faulty currents i.e. the over currents, earth faults, differential protections. The extra cores of a C.T. gets saturated as soon as the faulty currents starts flowing and thereby does not harm the main core of the transformer and the ammeter connected. The C.T. is always connected in the line carrying current. It first steps down the current to a measureable form and further gives this current to the ammeter.
