answersLogoWhite

0

On an electrical schematic it designates that the wires are all connected together. It is called a connection point.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Electrical Engineering

Wiring diagram for swamp cooler water pump?

pool pump wiring in what regard? To hard wire or not to hard wire? My choice would be to NOT hardwire and look at other alternatives to conserving power such as changing the type of pump to a variable speed pump - less draw on your power whilst having the ability for capacity power when you need it for manual vacuuming.


Why should there be no bare wire exposed after a wire nut is used?

Leaving any exposed bare wiring can lead to short circuit and breaker tripping. Most of the times wires in junction boxes are jammed into the back of the box. This is to allow for a device such as a switch or receptacle to be installed. Leaving exposed wire showing below the wire nut could allow contact with other exposed wires or it could come in contact with the bare ground wire which is also jammed in there. Good workmanship should prevail, only strip as much wire as needed to twist the wires together. Then install the wire nut. The skirt of the wire nut should project down over the insulation of the wire by a quarter of an inch. If it does not use a larger wire nut. This will provide full insulation protection to the wires in the junction box.


How long can the wires be for a 200amp service with 240 volt?

The wires can be as long as they need to be to make the connection. It is a fact that as the length of the wires are increased, the size of the wire also has to be increased, to over come the voltage drop due to the internal resistance of the wire. A 3/0 copper conductor with an insulation factor of 90 degrees C is rated at 210 amps. This is the normal size for a 200 amp service. If the service is further away, then the increasing of the wire size starts at 3/0.


How do you fix an electric baseboard heater?

first of all you buy a double pole unit thermostat which should come with the mounting plate and thermostat and it should have 4 wires 2 red 2 black okay now you join the red to the red power wire and black to the black power wire and the 2 remaining wires which should be a red and black can be joined to the red and black wires on your heater .....now you should be good to go ............LEE48


Can you build a ghost portal and how can you?

Idk , how to actually build a ghost portal but a portal for ghosts to come in all you have to do is face 2 mirrors together

Related Questions

Type of rays that come together?

The type of rays that come together are called convergent rays.


What are floceulants?

clumps of bacteria come together and impurities come together to form a cluster called as floc and the chemicals that are used for this purpose are called floceulants.


When two or more atoms come together it is called a?

It is called a compound.


Genes that come together with different alleles are called?

Genes that come together with different alleles are called linked genes. These genes are located close together on the same chromosome and tend to be inherited together during meiosis.


Parallel lines which come together at a vanishing point are called?

An illusion. Parallel lines, by their nature can never come together.


What is the out come if your plug wires and plugs were placed wrong and car was driven for 180 miles then switched to the normal order?

it will be ok if it is running fine now but sometimes it will jump time


What is it call when plates come together?

It is called a "convergent boundary".


The point at which supply and demand come together is called the?

equilibrium


What is the point at which waves come together?

The point at which waves come together is called the crest. This is the highest point of a wave where the energy is concentrated.


Why is the skin an example of organs?

Cells come together to form tissue. Tissues come together to form a functional unit called organs. The skin is simply tissues that come together to form several functions.


What do black dots represent in a wiring schematic?

A black dot in a wiring schematic diagram at a wire intersection represents a position where circuit wires are joined together. At a wire intersection where there is no black dot the wires cross over each other with no junction.


When two streams come together it is at this?

When two streams come together, it is called a confluence. At a confluence, the two streams merge to form a single stream.