0
A lumped network is made of physically separated R,L and C elements.harjinder singh is made by
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is difference between lumped and distributed elements?
simply defining Lumped elements are components available in market i.e., resistors,capacitors,inductors...... Whereas Distributed elements are inbuilt property( resistance,capacitance,inductance )of a connecting wire
What is an electrical network?
An electrical network is a system for supplying electricity in a given region.
What is noc engineer?
it means network operating center engineer, one who operates network.
Why is it that when the load exceeds the network capacity delay tends to infinity?
As load exceeds network capacity, packets gets jammed at nodes. These packets never go forward unless load goes below network capacity. Hence when load exceeds network capacity delay tends to infinity. As load exceeds network capacity, packets gets jammed at nodes. These packets never go forward unless load goes below network capacity. Hence when load exceeds network capacity delay tends to infinity.
What are the conditions in application of superposition theorem?
Superposition theorem can be applied if- 1) The network is linear 2) The solution of the network is unique
What is the difference between lumped and distributed network?
Lumped systems are those systems in which electrical properties like R, L, C etc are assumed to be located on a small space of the circuit. these systems are applicable for low frequency application. On the other hand Distributed systems assume that electrical properties R, L, C etc are distributed across the entire circuit. these systems are applicable to for high (microwave) frequency application. Unlike the lumped element model, it assumes non-uniform current along each branch and non-uniform voltage along each node.
What is mean by lumped element in electronics?
lumped" means that the dimension of you ckt element is much smaller than the wavelength of the signal passing through it. Therefore, you can treat your ckt element as a lumped unit (against the wavelength), and do not have to worry about wave propagation phenomenon "within" your ckt element. The opposite of "lumped element" is "distributed network." Typically, in low-frequency ckt/network, since the frequency is low, therefore, the wavelength is large (wavelength = propagation speed(usu. speed of light) / frequency ), so most elements can be treated as lumped. However, as frequency goes higher and higher, the wavelength becomes shorted and shorter, the wave propagation effect WITHIN the ckt element becomes more and more pronounced.
Why are the inner planets lumped together?
The planets are "lumped" together because they are in the gravitational pull of the sun.
What is lumped load?
A static load is a constant steady load.Think of a floor, if you stand on it without moving that is a static load. lump load A lumped network is usually a simplification of a distributed network, such as a transmission line. A transmission line has built in resistance, inductance
What is a lumped mass matrix?
A Lumped-Mass matrix, can be obtained by placing point (concentrated) masses, m_i, at node points i in the directions of the assumed displacement degrees of freedom.
What is the difference between lumped element and distributed element resonators?
The difference is that in a lumped element resonator, the circuit's elements are localized together. In a distributed element resonator, they are spread apart.
How the section of a transmission line can be used as lumped circuit element?
Actually in networks we will consider the elements like resistance, inductance, capacitance as lumped elements for simplicity, like this in power systems we will consider the transmission line parameters(resistance, inductance, capacitance) as lumped elements, because we will calculate all the parameters of power systems with respect to receiving end or sending end but not with respect to middle of the line. If a fault occurs on transmission line then we should not consider the lumped elements of that total transmission line, we should consider the lumped elements from sending end to the point where the fault is occurred.
What are the distributed and lumped circuit?
The circuit is callaed lumped circuit whose elements can seprate(eg rectifier circuit in pcb). but in the distributed circuit we can seprate the elements from the circuit(eg transmision lines)
What do you think of Muslims these days?
Most of them are not extremists & should not be lumped in with the terrorists.
Is transmissionline lumped element or distributed element?
transmissionline is a distributed element
How many helium nuclei lumped together make carbon?
3
What is a athroid?
There is no widely recognized term "athroid" in common language or scientific terminology. It may be a misspelling or a specific term that is not widely known or understood. Can you provide more context or clarify the term?
